Page 3 of 3 FirstFirst 123
Results 27 to 35 of 35
  1. #27
    Join Date
    Feb 2016
    Location
    Louisburg Kansas
    Posts
    3,759
    Post Likes
    Thread Starter
    Will do Brad. Feel free to email me also. I enjoy talking to all you guys.
    No man can be both ignorant and free.
    Thomas Jefferson

  2. #28
    Join Date
    Aug 2019
    Location
    Central Florida
    Posts
    105
    Post Likes
    I guess I am dumb , I cant figure out how to pm you . PM me your # and I'll call you .

  3. #29
    Join Date
    Feb 2016
    Location
    Louisburg Kansas
    Posts
    3,759
    Post Likes
    Thread Starter
    That's funny I have trouble with trying to PM or even answer a PM. My email address is in my profile. If you email me we can get around the PM.
    No man can be both ignorant and free.
    Thomas Jefferson

  4. #30
    Join Date
    Aug 2002
    Location
    Southold, NY
    Posts
    25,622
    Post Likes
    Quote Originally Posted by bradluke0 View Post
    I guess I am dumb , I cant figure out how to pm you . PM me your # and I'll call you .
    Only Pro Members can PM!

  5. #31
    Join Date
    Feb 2016
    Location
    Louisburg Kansas
    Posts
    3,759
    Post Likes
    Thread Starter
    I didn't know that pecmsr. Brad is probably eligible now for pro membership. Looks qualified to me.
    No man can be both ignorant and free.
    Thomas Jefferson

  6. #32
    Join Date
    Mar 2008
    Location
    kansas
    Posts
    1,712
    Post Likes
    Quote Originally Posted by WAYNE3298 View Post
    I didn't know that pecmsr. Brad is probably eligible now for pro membership. Looks qualified to me.
    Yup he has the posts just needs to fill out the application and send whiskey to twilli
    Honeywell you can buy better but you cant pay more

    I told my wife when i die to sell my fishing stuff for what its worth not what i told her i paid for it

  7. #33
    Join Date
    Feb 2016
    Location
    Louisburg Kansas
    Posts
    3,759
    Post Likes
    Thread Starter
    Finally got to the bottom of the problem. Early on I found some errors in the heat coil calcs and the circuit setters. I sent them to the engineer. Him and the vender got together and made the corrections. There was no official resubmittal so I thought my comments had been ignored. The engineer sent me their hand marked up corrections. They revised the heat coils, control valves and circuit setters. Calcs associated with the mark-ups are all good. The system can be balanced.
    No man can be both ignorant and free.
    Thomas Jefferson

  8. #34
    Join Date
    Aug 2019
    Location
    Central Florida
    Posts
    105
    Post Likes
    Its good to see they followed though . I am a bit disappointed in one respect though , I still think its better off wide open and let the 2-way control valves do their thing . BTW.....Many years ago we used to balance HCA hospitals all over the country . All of their heating was hot water reheat with 2-way control valves . We cleared it through HCA to not balance them . We checked the operation on them by checking the leaving air temp . Balance them or not , it just shows there is more than one way to skin a cat .

  9. #35
    Join Date
    Feb 2016
    Location
    Louisburg Kansas
    Posts
    3,759
    Post Likes
    Thread Starter
    I totally agree Brad and have made that clear to the engineer. Two-way equal percentage valves will do the job and all circuit setters do is add resistance to the water system. Three-way valves are a different story.
    This engineer is my favorite but I am disappointed he didn't send me an official resubmittal. It would have saved me a lot of grief. The final circuit setter picks are great. The valves are Nexus and some of the original picks had pressure drops from below one inch to seven inches water. Those pressure drops do not allow balancing.
    No man can be both ignorant and free.
    Thomas Jefferson

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •