Page 4 of 4 FirstFirst 1234
Results 40 to 47 of 47
  1. #40
    Join Date
    Jul 2011
    Location
    DFW, TX.
    Posts
    1,391
    Post Likes
    Quote Originally Posted by HE>I View Post
    Morning! Headed to the job now. Any advice for the start up sequence?
    Run through the ops manual. Piece of cake. Run through all the settings. Hallar at @DAD for the pro membership then you will get more responses. Cant do much in an open forum.

    Sent from my LG-G710 using Tapatalk

  2. #41
    Join Date
    Oct 2015
    Location
    Chino, Ca.
    Posts
    120
    Post Likes
    Thread Starter
    Quote Originally Posted by CEAS-AC-TECH View Post
    Run through the ops manual. Piece of cake. Run through all the settings. Hallar at @DAD for the pro membership then you will get more responses. Cant do much in an open forum.

    Sent from my LG-G710 using Tapatalk
    Pretty stoked, just got my pro membership!

  3. Likes CEAS-AC-TECH liked this post
  4. #42
    Join Date
    Jul 2011
    Location
    DFW, TX.
    Posts
    1,391
    Post Likes
    Quote Originally Posted by HE>I View Post
    Pretty stoked, just got my pro membership!
    Now ask this thread be moved to the locked forums

    Sent from my LG-G710 using Tapatalk

  5. #43
    Join Date
    May 2014
    Location
    Bay Area California
    Posts
    24,690
    Post Likes
    Or merge the two threads.


    Quote Originally Posted by CEAS-AC-TECH View Post
    Now ask this thread be moved to the locked forums

    Sent from my LG-G710 using Tapatalk
    If you were a real tech, you'd solder a relay on that board and call it good to go.

    I do a triple evac with nitro to remove non condensables.

    I use 56% silver on everything except steel.

    Did you really need the " If you were a real tech " ??

  6. Likes CEAS-AC-TECH liked this post
  7. #44
    Join Date
    Oct 2015
    Location
    Chino, Ca.
    Posts
    120
    Post Likes
    Thread Starter
    Quote Originally Posted by CEAS-AC-TECH View Post
    Now ask this thread be moved to the locked forums

    Sent from my LG-G710 using Tapatalk

    So, I dug a little deeper and found out that the factory setting was set to 67% indoor fan. I adjusted it to 100% and the capillaries and bottom of the indoor coil stopped frosting up and the pressures adjusted up to about 104 and 310. It was about 70 indoor and 70-75 outdoor.

    I think the low fan speed was the issue! What are your thoughts?

  8. #45
    Join Date
    Jul 2011
    Location
    DFW, TX.
    Posts
    1,391
    Post Likes
    Check the motor shive you probably can adjust it to speed the blower wheel up. Fact is you really should check the static pressure as that is a tell all.

    Sent from my LG-G710 using Tapatalk

  9. #46
    Join Date
    Jul 2011
    Location
    DFW, TX.
    Posts
    1,391
    Post Likes
    What are they expecting space temp wise from this unit? They wont get much bellow 70 given your suction readings...

    Sent from my LG-G710 using Tapatalk

  10. #47
    Join Date
    May 2018
    Location
    VA/DC
    Posts
    265
    Post Likes
    very possible. did you check the other items at all. I'm just curious

Page 4 of 4 FirstFirst 1234

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •