Page 1 of 3 123 LastLast
Results 1 to 13 of 36
  1. #1
    Join Date
    Jul 2002
    Location
    SE Texas
    Posts
    551
    Post Likes

    An E-Mail to Welbilt

    Good morning, Mr. Boakes. Thank you for responding. I apologize for taking so long to get back with you.

    The reason I asked to speak with someone higher up at Welbilt is because I am concerned with, what seems to me, frequent and expensive component failures in our relatively new Welbilt equipment in the past few years. I think someone in a management position should know about these failures. Here is a list:

    2 - Manitowoc Nugget Ice Machines. Failures were complete evaporator assemblies (000012319) in both of the machines and a gear motor assembly (000011126) in one of the machines. Another of our nugget machines is "growling" and I expect it to fail soon. In case you are wondering, the machines are cleaned and sanitized as outlined in the service literature and the water filters are changed as needed. All of these machines are less than 3-years-old.

    2 - Delfield Serving Line low wattage food wells with heat pads (3234798). After speaking with technical support, I learned that these particular wells, unlike conventional calrod heated wells, are not serviceable and the complete well needs replaced in the event of a heat pad failure. These two failures occurred within 6 months of each other on serving lines that are less than 4-years-old.

    On a smaller expense scale, we seem to be losing a lot of Danfoss 077F8529 (ETP R1) blue LED temperature displays on our refrigerated roll-ins and pass-throughs. The major issue with these displays is the fact that the LED numbers are partially failing and making it difficult to read the proper temperature. I was told by technical support that these failures are caused by water or moisture. I informed the support person that the displays have never seen a drop of water. Oddly enough, we haven't had any failures of the red LED temperature displays on our heated roll-ins and pass-throughs.

    Finally, on an even smaller expense scale, we lose a lot of 2190154 rocker switches. I buy them five at a time because they fail so often.

    So, this is my rant. I would appreciate any feedback you can offer. Thank you.
    With your chrome heart shining in the sun, long may you run.

  2. #2
    Join Date
    Mar 2015
    Location
    Hamersville, Ohio
    Posts
    6,412
    Post Likes
    Quote Originally Posted by SandShark View Post
    Good morning, Mr. Boakes. Thank you for responding. I apologize for taking so long to get back with you.

    The reason I asked to speak with someone higher up at Welbilt is because I am concerned with, what seems to me, frequent and expensive component failures in our relatively new Welbilt equipment in the past few years. I think someone in a management position should know about these failures. Here is a list:

    2 - Manitowoc Nugget Ice Machines. Failures were complete evaporator assemblies (000012319) in both of the machines and a gear motor assembly (000011126) in one of the machines. Another of our nugget machines is "growling" and I expect it to fail soon. In case you are wondering, the machines are cleaned and sanitized as outlined in the service literature and the water filters are changed as needed. All of these machines are less than 3-years-old.

    2 - Delfield Serving Line low wattage food wells with heat pads (3234798). After speaking with technical support, I learned that these particular wells, unlike conventional calrod heated wells, are not serviceable and the complete well needs replaced in the event of a heat pad failure. These two failures occurred within 6 months of each other on serving lines that are less than 4-years-old.

    On a smaller expense scale, we seem to be losing a lot of Danfoss 077F8529 (ETP R1) blue LED temperature displays on our refrigerated roll-ins and pass-throughs. The major issue with these displays is the fact that the LED numbers are partially failing and making it difficult to read the proper temperature. I was told by technical support that these failures are caused by water or moisture. I informed the support person that the displays have never seen a drop of water. Oddly enough, we haven't had any failures of the red LED temperature displays on our heated roll-ins and pass-throughs.

    Finally, on an even smaller expense scale, we lose a lot of 2190154 rocker switches. I buy them five at a time because they fail so often.

    So, this is my rant. I would appreciate any feedback you can offer. Thank you.
    That is Outstanding Sandshark!

    Hopefully, ... This will Wake Up Welbilt, & they will zealously seek to Improve their Equipment.
    Hos 4:6 My people are destroyed for lack of knowledge. Because you have rejected knowledge, I will also reject you, that you may be no priest to me. Because you have forgotten your God’s law, I will also forget your children.


    "You've got to Stand for Something or You'll fall for anything" (A. Tippin)


    Mat_15:24 But he answered, “I wasn’t sent to anyone but the lost sheep of the house of Israel.”

  3. #3
    Join Date
    Mar 2008
    Location
    kansas
    Posts
    1,287
    Post Likes
    Didn’t realize mani was combined with every other kitchen wall of shame participants . Is this a if we can’t beat’em just buy’em scenario
    Honeywell you can buy better but you cant pay more

    I told my wife when i die to sell my fishing stuff for what its worth not what i told her i paid for it

  4. #4
    Join Date
    Jul 2002
    Location
    SE Texas
    Posts
    551
    Post Likes
    Thread Starter
    Yeah, Welbilt owns Manitowoc, Cleveland, Delfield, Garland, Kolpak, Lincoln, Merco, Multiplex and a couple of others. I remember working on Delfield equipment back in the early 80s. I didn't like them then and I don't like them now. Like pretty much all manufacturers these days, low parts bidder gets the contract.
    With your chrome heart shining in the sun, long may you run.

  5. #5
    Join Date
    Mar 2008
    Location
    kansas
    Posts
    1,287
    Post Likes
    Quote Originally Posted by SandShark View Post
    Yeah, Welbilt owns Manitowoc, Cleveland, Delfield, Garland, Kolpak, Lincoln, Merco, Multiplex and a couple of others. I remember working on Delfield equipment back in the early 80s. I didn't like them then and I don't like them now. Like pretty much all manufacturers these days, low parts bidder gets the contract.
    Shame as you say some of those were crap and remain that way, at one time I considered mani one of the top manufacturers
    Honeywell you can buy better but you cant pay more

    I told my wife when i die to sell my fishing stuff for what its worth not what i told her i paid for it

  6. #6
    Join Date
    Oct 2011
    Location
    Chicagoland Area
    Posts
    7,550
    Post Likes
    Quote Originally Posted by crazzycajun View Post
    Shame as you say some of those were crap and remain that way, at one time I considered mani one of the top manufacturers
    Being one of the top, with only 5 big players in the restaurant ice machine business, isn't much. You've got Hoshi, Mani, Scottsman, IOM, and Cornelius.
    Officially, Down for the count

    YOU HAVE TO GET OFF YOUR ASS TO GET ON YOUR FEET

    I know enough to know, I don't know enough
    Liberalism-Ideas so good they mandate them

  7. #7
    Join Date
    Oct 2016
    Location
    Clearwater, Florida
    Posts
    1,103
    Post Likes
    I had a bit of a run-in with Welbilt 2 years ago, just got a new Convotherm 4 20.20 unit, had it for a little over a year or 2 and it's making this horrible sound when the bottom burner would fire. We called it the "Gunshot" because that's what it sounded like or a stack of pans hitting the ground.

    SO, up until this point a certain company was servicing them as they were under warranty so after the 1st or 2nd year the unit was out of labor warranty first, then parts warranty.

    I go to service it and when I pull the burner off I notice cracks around where the burner is sitting, on the metal wall seperating the electrical compartment to the oven cooking cavity.... Start to pull stuff off, combustion blower is partially melted, ignition control is partially melted, I'm astounded, what in the world?

    So I call Convotherm and I'm chatting away and I tell them what I see and so we hang up. I'm waiting for an email.

    "Unfortunately the warranty on this unit has expired"

    Ah, what?

    My answer was

    "Okay,

    Being this seems more like a mistake from either the factory or the tech from the service company that has been servicing the unit during the warranty period than a common wear type problem. Can we extend the warranty to cover this?"

    He then asks me what part, the blower or the module?

    All of it, dude.

    Anyways, long story short, I ended up getting a new ignition module, new blower, new heat exchanger (because why not?), new gaskets, igniters, and the 9. all overnight shipped from Germany, I installed the next day. Got authorization from Welbilt to weld the cracks myself which I did while waiting for parts and there ya go, 30 hour downtime but back up and running from dead in the water.

    So I understand where you are coming from, it seems the bigger companies don't care as much as they used to.

    They bought Crema international as well recently, now they are doing coffee also.

  8. #8
    Join Date
    Oct 2011
    Location
    Chicagoland Area
    Posts
    7,550
    Post Likes
    Quote Originally Posted by Olivero View Post
    I had a bit of a run-in with Welbilt 2 years ago, just got a new Convotherm 4 20.20 unit, had it for a little over a year or 2 and it's making this horrible sound when the bottom burner would fire. We called it the "Gunshot" because that's what it sounded like or a stack of pans hitting the ground.

    SO, up until this point a certain company was servicing them as they were under warranty so after the 1st or 2nd year the unit was out of labor warranty first, then parts warranty.

    I go to service it and when I pull the burner off I notice cracks around where the burner is sitting, on the metal wall seperating the electrical compartment to the oven cooking cavity.... Start to pull stuff off, combustion blower is partially melted, ignition control is partially melted, I'm astounded, what in the world?

    So I call Convotherm and I'm chatting away and I tell them what I see and so we hang up. I'm waiting for an email.

    "Unfortunately the warranty on this unit has expired"

    Ah, what?

    My answer was

    "Okay,

    Being this seems more like a mistake from either the factory or the tech from the service company that has been servicing the unit during the warranty period than a common wear type problem. Can we extend the warranty to cover this?"

    He then asks me what part, the blower or the module?

    All of it, dude.

    Anyways, long story short, I ended up getting a new ignition module, new blower, new heat exchanger (because why not?), new gaskets, igniters, and the 9. all overnight shipped from Germany, I installed the next day. Got authorization from Welbilt to weld the cracks myself which I did while waiting for parts and there ya go, 30 hour downtime but back up and running from dead in the water.

    So I understand where you are coming from, it seems the bigger companies don't care as much as they used to.

    They bought Crema international as well recently, now they are doing coffee also.
    I have to believe that eventually the chinese and mexican manufacturing is going to bite the manufacturers in the ass. I have to believe.....
    Officially, Down for the count

    YOU HAVE TO GET OFF YOUR ASS TO GET ON YOUR FEET

    I know enough to know, I don't know enough
    Liberalism-Ideas so good they mandate them

  9. #9
    Join Date
    Jul 2002
    Location
    SE Texas
    Posts
    551
    Post Likes
    Thread Starter
    Quote Originally Posted by Olivero View Post
    I had a bit of a run-in with Welbilt 2 years ago, just got a new Convotherm 4 20.20 unit, had it for a little over a year or 2 and it's making this horrible sound when the bottom burner would fire. We called it the "Gunshot" because that's what it sounded like or a stack of pans hitting the ground.

    SO, up until this point a certain company was servicing them as they were under warranty so after the 1st or 2nd year the unit was out of labor warranty first, then parts warranty.

    I go to service it and when I pull the burner off I notice cracks around where the burner is sitting, on the metal wall seperating the electrical compartment to the oven cooking cavity.... Start to pull stuff off, combustion blower is partially melted, ignition control is partially melted, I'm astounded, what in the world?

    So I call Convotherm and I'm chatting away and I tell them what I see and so we hang up. I'm waiting for an email.

    "Unfortunately the warranty on this unit has expired"

    Ah, what?

    My answer was

    "Okay,

    Being this seems more like a mistake from either the factory or the tech from the service company that has been servicing the unit during the warranty period than a common wear type problem. Can we extend the warranty to cover this?"

    He then asks me what part, the blower or the module?

    All of it, dude.

    Anyways, long story short, I ended up getting a new ignition module, new blower, new heat exchanger (because why not?), new gaskets, igniters, and the 9. all overnight shipped from Germany, I installed the next day. Got authorization from Welbilt to weld the cracks myself which I did while waiting for parts and there ya go, 30 hour downtime but back up and running from dead in the water.

    So I understand where you are coming from, it seems the bigger companies don't care as much as they used to.

    They bought Crema international as well recently, now they are doing coffee also.
    At least you got something out of them. We have two OGS10.10 Convotherms that the stainless steel inside the cooking compartment started rusting within a month of installation. They warrantied the first time, but when the replacements started rusting again, they sent out a company to test our water. Of course, it was the water's fault, even with the high dollar Claris water filter system and ConvoCare wash and rinse chemicals. They voided our remaining warranty.
    With your chrome heart shining in the sun, long may you run.

  10. #10
    Join Date
    Mar 2008
    Location
    kansas
    Posts
    1,287
    Post Likes
    Quote Originally Posted by 2sac View Post
    Being one of the top, with only 5 big players in the restaurant ice machine business, isn't much. You've got Hoshi, Mani, Scottsman, IOM, and Cornelius.
    hoshi and mani I thought were the top two when it came to freezing water. I remember when you bought the case and set the refrigeration unit on top with mani. Reach ins
    Honeywell you can buy better but you cant pay more

    I told my wife when i die to sell my fishing stuff for what its worth not what i told her i paid for it

  11. #11
    Join Date
    Mar 2007
    Location
    In the Conservatory with a Lead Pipe
    Posts
    15,679
    Post Likes
    Manitowoc Food Service Changed its name to Welbilt in 2017

  12. #12
    Join Date
    Mar 2007
    Location
    In the Conservatory with a Lead Pipe
    Posts
    15,679
    Post Likes
    I remember back in the early 90's being at the Manitowoc factory and the old CEO dude saying Manitowoc will never make a flaker...
    “If You Can Dodge A Wrench You Can Dodge A Ball”

  13. #13
    Join Date
    Mar 2015
    Location
    Hamersville, Ohio
    Posts
    6,412
    Post Likes
    Quote Originally Posted by 2sac View Post
    I have to believe that eventually the chinese and mexican manufacturing is going to bite the manufacturers in the ass. I have to believe.....
    I Agree 2sac.

    I also Believe that America's Corporations/ Manufacturing plants overseas is soon going to cause America to have a Major Case of Hemorroids when it comes to Service parts & HVAC/ Refrig/ Kitchen Equipment.
    Hos 4:6 My people are destroyed for lack of knowledge. Because you have rejected knowledge, I will also reject you, that you may be no priest to me. Because you have forgotten your God’s law, I will also forget your children.


    "You've got to Stand for Something or You'll fall for anything" (A. Tippin)


    Mat_15:24 But he answered, “I wasn’t sent to anyone but the lost sheep of the house of Israel.”

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •