-

Originally Posted by
spliskin
It's illegal to not put an ECM back in. Sucks but just so you know. CYA

Originally Posted by
UmmScott
Please provide proof...?
Sent from my SM-N920V using Tapatalk
X 2
-
I have had tons of failed EC motors on Russell evaps. I spoke to the factory and is seems they purchased a few containers of Chinese motors that had defective software. No service bulletin that I know of. They just send out replacements.
-
Post Likes - 1 Likes, 0 Dislikes
-

Originally Posted by
jmlandru
I have had tons of failed EC motors on Russell evaps. I spoke to the factory and is seems they purchased a few containers of Chinese motors that had defective software. No service bulletin that I know of. They just send out replacements.
Lets see I was told the motors are fighting each other.
Keep us informed on the newer motors please.
-

Originally Posted by
pecmsg
Lets see I was told the motors are fighting each other.
Keep us informed on the newer motors please.
Sounds like the motors are really fighting the moisture that gets trapped inside. What a $hit show.
-

Originally Posted by
ammoniadog
Sounds like the motors are really fighting the moisture that gets trapped inside. What a $hit show.
I agree.
I'm very surprised as to why, what appears to be a common issue with ECMs used in refrigeration, can't be resolved simply by something like encapsulating or potting the printed circuit boards (PCBs) on these motors to protect the electronics from the inevitable moisture intrusion. Heck, it shouldn't be that expensive and certainly would cost a lot less than replacing in-warranty failures by the boatload.
These motors should be able to run totally submerged for several weeks or more in my opinion.
Here's an interesting article discussing such protections for electronics: https://www.electrolube.com/technica...h-do-i-choose/
-

Originally Posted by
icemeister
I agree.
I'm very surprised as to why, what appears to be a common issue with ECMs used in refrigeration, can't be resolved simply by something like encapsulating or potting the printed circuit boards (PCBs) on these motors to protect the electronics from the inevitable moisture intrusion. Heck, it shouldn't be that expensive and certainly would cost a lot less than replacing in-warranty failures by the boatload.
These motors should be able to run totally submerged for several weeks or more in my opinion.
Here's an interesting article discussing such protections for electronics:
https://www.electrolube.com/technica...h-do-i-choose/
The same thing happens in air conditioning applications. Even after they started encapsulating the circuit boards, motors fail for no good reason.
Sent from my Moto Z (2) using Tapatalk
-

Originally Posted by
shellkamp
The same thing happens in air conditioning applications. Even after they started encapsulating the circuit boards, motors fail for no good reason.
Sent from my Moto Z (2) using Tapatalk
If they can't find a motor that'll stand up to basic walk-in cooler/freezer conditions, then they should stop selling these units until they do. If the price turns out a lot higher, that's the price of trying to be Green. Complain to your tree-hugging representatives in Congress about that.
-

Originally Posted by
icemeister
If they can't find a motor that'll stand up to basic walk-in cooler/freezer conditions, then they should stop selling these units until they do. If the price turns out a lot higher, that's the price of trying to be Green. Complain to your tree-hugging representatives in Congress about that.
There too busy dodging old girlfriends!
-
Its always amazed me how the open air motors last through the abuse in coolers and freezers
On the same token i never imagined a totally sealed ecm motor filling up with water...
-

Originally Posted by
Snapperhead
Its always amazed me how the open air motors last through the abuse in coolers and freezers
On the same token i never imagined a totally sealed ecm motor filling up with water...
Makes you wonder if an open frame ECM motor would hold up better.
Sent from my Moto Z (2) using Tapatalk
-

Originally Posted by
icemeister
If they can't find a motor that'll stand up to basic walk-in cooler/freezer conditions, then they should stop selling these units until they do. If the price turns out a lot higher, that's the price of trying to be Green. Complain to your tree-hugging representatives in Congress about that.
And just where would their job security be if they actually solved a problem?
Sent from my Moto Z (2) using Tapatalk