X2. I worked for a company that help control kitchen exhaust systems with a lot of work for one client. Their setup varied with every build. You would think they would try and stick to a similar...
Type: Posts; User: BALloyd
X2. I worked for a company that help control kitchen exhaust systems with a lot of work for one client. Their setup varied with every build. You would think they would try and stick to a similar...
Those units are designed for each job. Call Engineered Air with the serial number and they will tell you.
I believe that indoor air handler also limits how low you can set the temp. Not sure Kumo cloud will help with that.
@FlyersFan
So you know you will get zero warranty installing Mitsubishi equipment yourself right? You cannot even register it unless you are a contractor. Where are you going to get the equipment? At one point...
Who sized this equipment?? Likely massively oversized and you are going to have massive overheating problems in the winter set up like that.
https://www.simplecircuitdiagram.com/1930-permanent-split-capacitor-capacitor-run-ac-induction-motor/
Incoming power wire goes straight to the main winding. The other incoming power goes to the...
Look up 4-wire stepper motor......
Look at it as investing in yourself. If you take the pre-employment program seriously, you can learn a few basic things about HVAC/R that might give you a leg up on someone who is totally green. You...
Did they use the Schwank flexible gas connectors to attach each heater to the gas line or did they use another brand? Those connectors have a btu rating associated with them based on length and...
2" on NG at 8" H2O at 300 feet is good for approximately 1.2 million btu's. Sounds like there might be something else at play.
You often add ducting to deal with this. Rheem allows this on their heat pump water heaters. Instructions in the installation manual.
Made some Prime rib for dinner.
868619868621
This is a slightly different install than a PTAC but it is a 115V inverter unit.
https://olimpiasplendidusa.com/wp-content/uploads/2022/06/6736_202107_Maestro_Pro_12_HP_Spec_Sheet_081220.pdf
The IEC is an open work permit for 2 years. The guy can literally go and work for any employer in the entire country. He doesn't need to even need to apply to BS jobs with low pay, use your own...
You are not tied to any employer. Prove your experience and you definitely won't be making minimum wage. I wouldn't even take a job offering minimum wage.
Carrier owns ICP. You are more likely to find a Carrier or Bryant dealer in Canada than an ICP dealer....
You will be fine with 7/8". As you have figured out, the efficiency loss is minimal in most cases. The manufacturer is just suggesting the bigger size because they gained all their efficiency ratings...
Why not? You can order a manual D book off the interweb.....
No where in my post did I say I have never heard of energy consumption usage monitoring. Please point out in my post where I said that....you won't find it. Stop inferring things that were never...
Once again you keep asking for detail information yet keep providing vague responses to questions. Garbage in, Garbage out.
Give me a model number of an electrical panel that tracks energy...
The is no lack of work for qualified HVAC/R techs in Canada.........
Please explain the methods all these numerous people you are referring to are measuring the electrical usage of their MItsubishi ducted h2i heatpumps.
How old are you? You might be able to get an International Experience Program visa for two years in Canada. It would be an open work permit for 2 years.
RX-11 is a waste of time on a clean system. Just use N2. The whole oil mixing myth was busted long ago....your system won't die with a small amount of mineral oil in it.
What happens if you force them into emergency run?
6 month dry aged kelbosa?
Chicken dinner? Lol
Ding ding ding.....winner.
I can call my accountant at anytime and give him a dollar figure and he can tell me within 5 minutes or less what my approximate tax bill will be for that amount. Easily...
What is the cooling load? Unless it differs significantly from the heating load, then your contractor should be installing a 12000 btu hyperheat with a 5kw backup. No point in doing a manual J if you...
Not sure what partial load charts people are referencing. The KP units not going below 50 percent is documented.
There is special iron infused copper alloy that is allowed in some applications. Seen it used on some CO2 market installs.
Which thermostat is being used?
You better find some else to do installations either yourself or a quality sub contractor you can trust. Otherwise, you will stand a good chance of coming back to service some complete hackjob and...
x2. Factories are not perfect. Might be factory undercharge????
Should look for heavy duty mechanics that work in camp then......they work in all our crappy conditions, but also usually add in some mud. Probably find HVAC/R conditions like a vacation.
The duct work could possible be sealed up with a system called Aeroseal, but that doesn't solve your insulation problem. Time to start opening walls and ceilings.....
Not on a Mitsubishi Air Handler unless they wired in the SPTB1 kit. The fan will get power from the outside unit and operate normally. The breaker on the heat kit only shuts off power to the electric...
I would question a lot of their minimum cooling rating data. Some of it does not match Carrier's published data at all. For example, the indoor cassette, Carrier states a minimum of 4000 btu's vs...
Where are you getting your information?? All the COP heating ratings are over 1.75 COP regardless of indoor unit style. I doubt cooling efficiency would be 1 to 1
I agree....backhoe or bust. Way more versatile.
https://cdn.daikincloud.io/PIM/Assets/Documents/SM-FTXM_V-RXM_V%20(SiUS042113E).pdf
Page 156
Has he tried running it with the cover off?
So you have forced air already with a furnace?
If so why is the installer running heads all over the place? Could either swap in a Mitsu airhandler and outdoor unit or us the Mitsu add on coil for...
I feel like I have seen used boxes in better shape than that new one.
Is this when only the 6000 btu head is calling? My understanding was that this is the outdoor unit is at it minimum turn down and the capacity is still too high for the one zone, so it bypasses...
You posted the same question on Reddit. Google search talks about a York recall regarding said problem on another thread on Reddit.
Looks to me like the HVAC installer just used a piece of downspout as a hide instead of the HVAC specific line hide.
First off, it enters your soffit and not the gutter, so it was never part of...
Have you checked out all the training videos on Wrightsoft's website? There are a lot of them and they are very detailed.
Time for a new technician.....
Welcome back