Search:

Type: Posts; User: jmeadows

Search: Search took 0.01 seconds.

  1. Thread: HONEYWELL EIM

    by jmeadows
    Replies
    8
    Views
    441

    Thanks guys for the answer. I mainly work on...

    Thanks guys for the answer. I mainly work on single stage non communicating equipment . A lot of time when I go into a house there will be a Honeywell 3000 or just a typical stat. What does...
  2. Thread: HONEYWELL EIM

    by jmeadows
    Replies
    8
    Views
    441

    HONEYWELL EIM

    I was doing a service on a zones heat pump. I saw the standers zone board but connected to it was a EIM board . I pulled the t stat off of the wall and found that there was only 2 wires going to it ....
  3. Replies
    20
    Views
    1,042

    Then yes I would say that the head pressure is a...

    Then yes I would say that the head pressure is a bit excessive . Usually you will have a condensing temp over ambient of 30 to 40 degrees in heating mode which would be your indoor temp because the...
  4. Replies
    20
    Views
    1,042

    Well the head pressure is related to what the...

    Well the head pressure is related to what the indoor return air temp is in heating mode . Without knowing what that indoor temp is it is hard to say if your head pressure is excessive or not .

    ...
  5. Replies
    8
    Views
    608

    It sounds low on charge . In the heating mode I’m...

    It sounds low on charge . In the heating mode I’m guessing you just had your manifold hooked up in the standard cooling configuration. Low side hooked up to the suction line and the red hose hooked...
  6. Replies
    3
    Views
    613

    Thanks for all of the responses it was a lot of...

    Thanks for all of the responses it was a lot of help


    Sent from my iPhone using Tapatalk
  7. Replies
    11
    Views
    832

    I know this is going to sound like a really...

    I know this is going to sound like a really elementary question but I don’t see how you would even get subcooling if you had your low side hose attached to your true suction port and your high side...
  8. Replies
    11
    Views
    832

    Refrigerant charging question

    In the summer I rely heavily on superheat and sub cooling to tell me if the refrigerant charge is ok , as well as diagnose issues . I was wondering if there is a definitive way to tell whether or not...
  9. Replies
    16
    Views
    1,123

    Are you referring to the green pumps that are in...

    Are you referring to the green pumps that are in a lot of Taylor style wood stoves ?


    Sent from my iPhone using Tapatalk
  10. Thread: Cap question

    by jmeadows
    Replies
    32
    Views
    1,986

    No Iíve piggybacked caps to get the proper size...

    No Iíve piggybacked caps to get the proper size when I didnít have the right one . I have also added a slightly higher mfd rated cap on to get a customer by until I could get the right one . In...
  11. Replies
    3
    Views
    613

    Heil heat pump defrost board question

    Today I was working on a Heil heat pump Model # HSH530GKA200 Serial # E171813494 . While I was taking amp draws and checking refrigerant pressures I noticed there was a VS and VR terminal on the...
  12. It would help if you included superheat and sub -...

    It would help if you included superheat and sub - cooling


    Sent from my iPhone using Tapatalk
  13. Thread: Confused

    by jmeadows
    Replies
    7
    Views
    752

    Unfortunately , I did not get back there today ....

    Unfortunately , I did not get back there today . The customer was not available . When I was in the programming menu for the Nest it gives you the option to chose dual fuel . However it doesn’t let...
  14. Thread: Confused

    by jmeadows
    Replies
    7
    Views
    752

    Yeah it actually started on high stage for about...

    Yeah it actually started on high stage for about 5 to 10 seconds and then dropped back to low fire. While on that call I had to remove the thermostat that was there and install a nest thermostat that...
  15. Thread: Confused

    by jmeadows
    Replies
    7
    Views
    752

    Oh ok so you would have to wait for a allotted...

    Oh ok so you would have to wait for a allotted amount of time before you could check your second stage gas pressure ? I wonder if there is a way to manually put it into 2nd stage ? Thanks for the...
  16. Thread: Confused

    by jmeadows
    Replies
    7
    Views
    752

    Confused

    Itís been a while single Iíve been on this forum . For most of my heating and air career I worked in myrtle beach . With that being said I didnít work on a lot of gas furnaces . Now living in...
  17. Replies
    21
    Views
    3,089

    Oh ok haha .

    Oh ok haha .
  18. Replies
    21
    Views
    3,089

    What is a PHM Approach ?

    What is a PHM Approach ?
  19. Replies
    21
    Views
    3,089

    In response to what Core_d said I would only...

    In response to what Core_d said I would only weigh in the charge if I opened up the system . I was mainly concerned with getting an accurate reading for subcooling on a rtu. After all of the...
  20. Replies
    64
    Views
    5,660

    Ive never had any issues with installing them...

    Ive never had any issues with installing them upside down , as long as they are properly strapped up . I have had issues when the cap is not secured properly and shorts out against the side of a...
  21. Replies
    21
    Views
    3,089

    Thanks guy for all of the quick responses and the...

    Thanks guy for all of the quick responses and the welcoms . In reference to what bazooka joey said , I mainly work on rtus 10 ton and above , a lot of York predators etc . To be more specific I...
  22. Replies
    21
    Views
    3,089

    New to commercial Hvac

    Hey Guys , My name is Josh ive been doing residential hvac for the past three years . This past year I have been doing commercial . While I understand A lot of what is going on I still have many...
Results 1 to 22 of 22