Search:

Wolf steel/Napolean condo pack
Model # P-C30A-A18A A
i was having problems with this unit going off on a pressure switch open while ventor on fault (2 flashes) unit installed Nov 2019. The issue...

Yes it was the secondary leaking and I'm still fighting with wolf Steel about it.

Ya if i cut the hole open more i should be able to, i havent been back yet

Wow, i haven't had that many problems with them, but i did have a callback on ignitors failing which there was a recall on and the tech support said they had a problem with these seals but they...

Thank you for the input, appreciate it,
It is going off on limit because the duct work is restricted, i am not sure how the old one worked but the return is just a box in the crawl with 2 - 6"...

I've honestly never seen it before and i have been in the trade for 15 years, is it just communicating stats that do this?

Also I did check for CO and did not get any reading inside the house or the plenum, which i was worried about if the secondary seal was leaking, but i think it still could be leaking water without...

New Continental (Napolean/wolf steel) 96% 2 stage furnace leaking water, installed last winter, had problem with water leaking after install, tech went and changed collector box and gaskets, it was...

Just had installers install new 96% 2 stage carrier downflow with new AC and edge thermostat. Customer called few days later because of no heat, found it going off on limit, gas pressure wasn't...

Do you do the same thing?
And yes he has more call backs then i think is normal, they come in spurts

I agree with you 100% and do the exact same thing except i usually just have my manometer in my hand cause i dont like going in and out.... but the whole point is the first thing on your list is a...

Lol i dont think hes going through fuses, i dont think hes that bad, but its bad enough that he says he doesnt need a meter and when he jumps something and it works then he knows what part is the...

So it wouldnt be wrong of me to tell him he has to take his meter into every call then if its a safety concern.

He does have one of those light up testers but i dont know about you, but i cannot...

Thats what this guy does and hes never gotten a call done in less than an hour it drives me crazy. Goes in no tools, walks back out has a smoke and goes back in with some tools, forgets something...

Wage depends on experience and licenses but if for a G2 with a 313D or 313A it would be $25-$30/hour for residential
There is a whole health benefits package that includes 80% on prescriptions,...

Are you looking for a job in Windsor On??

When doing No heat and no cooling calls, how many of you bring your meter in on every call?
I think this is a stupid question as i do on every single call BBBBBUUUUTTTT I just had an employee tell...

Looking for service techs, lead installer and a helper in windsor Ontario.
Good wages and benefits. Great smaller company to work at! Apply with resume to my email!

I think you are right, its been 10 days since going there, just waiting to see if it happens again

Thank you for the manual, i could jot find that one amywhere! 6 flashes says HSI failure which is strange because it looks good and ohms out ok. I was thinking it may be the board because its...

Thats the thing it works fine every time i go there. But once when i arrived it flashed 6 times. Thats the only time i saw that fault and theres nothing that says flash codes. I pulled hose of...

Lennox mid efficiency g24m3-75a-1
This furnace has one LED light not two and i cannot find the flash codes anywhere. Does anyone have this?
I keep getting six flash code and cant figure out whats...

Hi guys, I have been on this site for about 7 years and in the HVAC industry for 12 years, my commonlaw wife was diagnosed with cancer about a year ago. We just found out it is very aggressive and...

Thank you! I will keep you posted

I will post diagram tomorrow while im there.

No pic of the diagram, sorry I didnt see the reply until now. Found a melted pin connector At the condenser fan motor and saw a spark from there while running. First time I actually saw the fuse...

Both fuses blown*

working on a Lennox rooftop unit 575 volt envy first visit there I found the fuses for the condenser fan motors both alone replace the fuses and checked for shorts to ground and checked relays and...

Also how does the sprayer work? air compressor? hand pump? sorry guys no one at any company ive worked at has ever had one

To you guys that use tank sprayers, this might sound like a stupid question but what do you rinse the coil with afterwords, ive never used one, i do maybe 10-12 commercial maintenance jobs myself and...

Can you email me prices and pics on the recovery machine, turbo torch and vacuum gauge? Thanks

Ya randys a good teacher!

I'm in advanced at mohawk right now, I'm going to write in january hopefully, I heard there was 4 different tests and some were harder then others I can't wait to get it over with tho

Working on a carrier M# 50rhr036scc51130
S# 3805v19316
Keeps locking out, can't figure out why water into the unit 80f water out 125f
Suction pressure 75 psig
Discharge,before entering condenser...

so that is a seperate device? do u have a website?
thanks

Does anyone have an all in one hvac tool that you can input info to determine superheat, p/t charts, ductulator and heat load all in one? and how do you like it?

would you prefer a hand held...

So it will be R408A in the system will it not?

Its on for about 10 minutes before it has a heavy frost on it back to the compressor and eventually starts to ice up

I got a call today for a Hoshizaki Ice Maker, model KM-250BAC, i dont really work on ice makers that often so any help would be appreciated, It has a Copeland Compressor M# RSU4-0050-1AA-908
S#...

Lmao!!! sorry i didnt even know they gave me the professional member!

well can i get an answer because they never gave me a proffesional membership, i have probably 50 posts and you only need 10 for proffessional and i have my g2 and has been to school twice for...

confused:What is the best things to do for a residential boiler maintenance, i usually, clean the burners check gas pressure, check expansion tank pressure, bleed air at bleeders if needed, amp pump,...

your right i shouldnt think the same scenario before i get there, but ive always been meaing to ask about these high pressure switches on those units, because i have reset them before and never gone...

On the old lennox condensers, i dont have the numbers with me but those old grey ones, they have a red reset button for high pressure underneath the electrical access panel or above the gauge ports,...

I dont work on chillers that often but i am required to change a compressor on a trane chiller for a customer of ours, what steps are required that would differ from a commercial rooftop package...

I was working on a yorkrooftop unit last week and the breaker in the disconnect (100amp 3 phase commander breaker) was no good, i had proper voltage at line side and missing 1 leg of 3 phase on load...

I was working on a bradford white hot water tank today the M# is MITW40L6BN15
S#BF6365642

Tank would ignite and run for 10 to 20 sec and flame would shut off, it would do this over and over...

My company always hires out air balancing on commercial jobs, is there any course or any good way to learn air balancing? i know you need some expensive tools for it but i dont know anything about...

Has anyone ran into this problem? i have seen it a few times... people with 30 or 40 year old olsen or clare heckla low boys changing from a mechanical t-stat to a cheapo digital programmable...

what is the best zebra analyzer?