Search:

I would also appreciate the signed modules as well. Thank you in advanced


Sent from my iPhone using Tapatalk

You need to perform a backup and after loading firmware, restore the backup.


Sent from my iPhone using Tapatalk

This Siemens system is 100% proprietary. The field panels will need to be replaced as there is not a driver that will talk to these P2 devices effectively. Most of the P1 devices can be integrated...

Mp580 and mp581 are fully programmable.


Sent from my iPhone using Tapatalk

You’ll have to reach out to your local Trane office. Most likely that will not sell to you, but good luck.


Sent from my iPhone using Tapatalk

You won’t have any issues writing to these point.


Sent from my iPhone using Tapatalk

I’m doing a controls upgrade on a large AHU. Most of the control has previously been converted from pneumatic to DDC, except for the 1/3 2/3 steam preheat valves and the actuator for the preheat face...

There is a p1 driver for Niagara. If all you have is common TEC application such as 2020 it is pretty seemless. If there are other FLN controllers such as DPUs, MPUs and UC controllers you’ll have...

Correct, I’m referring to a separate P2 driver that plugs into the rj11 hmi port of the Siemens device. I will verify the vendor


Sent from my iPhone using Tapatalk

The Apogee 600 TEC driver can not be used to pull in the PXC.

As mentioned earlier the two ways to accomplish this are the P2 driver or using the Insight server to export via BACnet.

The...

JCI DX9100(s) n2 with expansion modules
JCI FX16(s) n2 with expansion modules
Siemens PXC(s) p2
Siemens MEC p2
Make offer.


Sent from my iPhone using Tapatalk

Not sure this answers your question. But this would show you at which priority a point is written to by another device. In your facets add “priorityArray” as a boolean equal true.


Sent from my...

Verify that you do not have the BACnet discovery enabled in Siemens system profile. If this is enabled it will try to discover all the devices, and will put a lot of “who is” traffic on the network. ...

Trane Tracer TU is needed to configure the uc600.


Sent from my iPhone using Tapatalk

I think you that you are stuck without Tracer TU.


Sent from my iPhone using Tapatalk

How bout just opening a web browser. If it's remote set it up in your router with an external ip.


Sent from my iPhone using Tapatalk

If you are a service customer than you can most likely purchase Tracer TU from you local rep, it's at least worth a call if your not. There is also yearly licensing fee.


Sent from my iPhone...

The USB connection on the BCI is used to connect that tool.


Sent from my iPhone using Tapatalk

Pre-apogee is a term that refers to the firmware. It is pre-apogee


Sent from my iPhone using Tapatalk

First device is a PXC, second is a pre-apogee MEC and third is an MBC with a power open Processer (apogee).
All devices are communicating P2 proprietary RS485 communications. MBC and MEC are...

This is set in Tracer TU. Should be automatic for the start up tech, but unfortunately a BAS technician is rarely a part of this process if he's not involved in the project.


Sent from my iPhone...

We'll need a lot more info, pneumatic, ddc?? Control system?


Sent from my iPhone using Tapatalk

Do you have the ai-fi connected through an SC?


Sent from my iPhone using Tapatalk

UC210 can be application specific as well as custom configurable. Do you have a specific application your looking for?


Sent from my iPhone using Tapatalk

The price Siemens will give you would be for them to install. I've installed this myself but Siemens said that I wouldn't be able to do it. That's before they'll found out I'd worked for Siemens for...

It's extremely marked up. All points are not exposed. You need to creat an export table in the insight software.


Sent from my iPhone using Tapatalk

That is a Trane uc210


Sent from my iPhone using Tapatalk

Is the set point dial enabled? Also is CTL STPT overridden? I only assume with the info you have that the set point dial is disabled. And you CTL STPT equals your DAY HTG STPT.

There is an FLN driver, but will only communicate to generic tecs. Custom applications and any extended io such as dpu, mpu and bims will not be discovered. Does the current insight server have the...

The SystControl is what you want, you'll be able to see all your indoor units as well as the outdoor unit.


Sent from my iPhone using Tapatalk

The driver is very limited.


Sent from my iPhone using Tapatalk

You will not ba able to see many devices when using a p1 driver. Expansion modules such as pxms and bims, UCs DPMs and certain TEC applications.


Sent from my iPhone using Tapatalk

I got water drops in my otterbox and phone started going crazy. Giving a 1.5 year old a bath will do that.

Sent from my SM-G900V using Tapatalk

Sent from my SM-G900V using Tapatalk

V'''v:v:v:v:vv::v:::v:'vv''vçcccccccccccccccccccccvvvv:::::vvv::::::::::::::vvvvvv vvv

Sent from my SM-G900V using Tapatalk

You only need to hook up to one panel on a single P2 network. Huge downside to that is the more points you have in point monitor the slower this solution will be. Your expectation shouldn't be to...

No, you can not hook up the trunk interface to the jace, your only options are to use the csi driver thu the mmi port or if the insight server has a bacnet license, you can export the points via...

Just found out on a lochenvar integration I'm currently doing, lochenvar is now installing bacnet cards in the boiler and will no longer need the protonode. I'll be disovering these Friday to...

Are you designing this system yourself? Is Siemens your only option? Where are you located?

Sent from my SM-G900V using Tapatalk

The instance number applies to mstp as well.

Sent from my SM-G900V using Tapatalk

Lochenvar has a field server that is pre configured modbus to BACnet, used them several times with ease.

Sent from my SM-G900V using Tapatalk

Wcis is the program you will need to connect to a tec. The max line driver only supports standard applications, it will not discover an dpu. Mpu or uc controller or special tec applications such as...

There is a background object that is not defined. They can drive you crazy, especially if there is a lot of lot of associations. Good luck.

It probably needs to be replaced. Are you writing to any of the subpoints excessively?

Firmware upgrade can only be for through com tools which is a not distrusted. Calling your local branch is your only option to upgrade.

Try network 9

Have you discovered the devices thru the Web browser, and verified all your devices were pulled in. There you should see your instance numbers.

Do datamate or wcis have a terminal emulator? I think they may, I'm used to using hyperterminal, dont remember what the keystrokes are to enable ethernet, you'll also need administration...

The 2.8 panels are made ether net thru hyperterminal. The earlier controllers will need to be flashed by Siemens

I'm doing a pharmaceutical job where, I am using Vaisala current temp and humidity sensors. The customer has a third party validation company that wants to split and repeat my current signal to use...