Search:

Type: Posts; User: Garrettv

Search: Search took 0.02 seconds.

  1. Replies
    18
    Views
    18,819

    Another note I also wouldn't recommend leaving...

    Another note I also wouldn't recommend leaving probes inserted long term if you wanted change out fittings and use one of those CPI gauges with a tee
  2. Replies
    18
    Views
    18,819

    Lube the probe with water based lubricant they...

    Lube the probe with water based lubricant they will fit !
    They are tight and I always worry when pushing them in as Well I have never seen a temperature and pressure gauge that fits those in one...
  3. Thread: Ice box

    by Garrettv
    Replies
    6
    Views
    808

    You may want to bow out of this one it will cost...

    You may want to bow out of this one it will cost the customer lots and could cause you more grief then it's worth if you don't work on this stuff normally
  4. Replies
    6
    Views
    1,110

    As long as Honeywell publishes a " conversion "...

    As long as Honeywell publishes a " conversion " instructions ( as it seems they do from above ) then all is good. If you just swapped it for something else you could be affecting the units original...
  5. Thread: Soft serve

    by Garrettv
    Replies
    7
    Views
    1,073

    The dukes I have worked on I either used same...

    The dukes I have worked on I either used same compressor with a drop in I think rs52 ? Or a 404 compressor not much problems with either other then adjusting temp controls for proper ice cream...
  6. Thread: Gas pressure

    by Garrettv
    Replies
    20
    Views
    2,241

    I believe most you can de rate a furnace is 80%...

    I believe most you can de rate a furnace is 80% of rated capacity but never over fire a unit
  7. Thread: Roof Top Unit

    by Garrettv
    Replies
    119
    Views
    8,383

    I just checked my p/t chart and this is what I...

    I just checked my p/t chart and this is what I will go with for r22
  8. Thread: Roof Top Unit

    by Garrettv
    Replies
    119
    Views
    8,383

    So when do you find out answer ? I am thinking...

    So when do you find out answer ? I am thinking refrigeration side is functioning normally I believe unit is under sized for heat load of building or there is an abnormal heat load on system during...
  9. Replies
    3
    Views
    1,195

    Probably none ! Or a G3

    Probably none ! Or a G3
  10. Replies
    26
    Views
    4,845

    If your getting flashing at Evap after a long...

    If your getting flashing at Evap after a long line set the liquid line has been sized wrong to much pressure drop in the line, and when does looks take president over functionality in refrigeration?...
  11. Replies
    8
    Views
    1,420

    Sounds like compressor valves are done

    Sounds like compressor valves are done
  12. Replies
    179
    Views
    28,696

    Pretty smacna says all fiborous duct liner should...

    Pretty smacna says all fiborous duct liner should be sealed or edges capped with sheet metal to stop fibres from getting into air stream
  13. I have this filter in my home and little ozone...

    I have this filter in my home and little ozone smell ( when air handler is in low speed cooling or heating ), works good and is same technology as used in hospitals ( so i have been told ) and...
  14. Replies
    4
    Views
    819

    410 low on gas probally **** coil

    410 low on gas probally **** coil
  15. If he thinks ontarios tests are hard I question...

    If he thinks ontarios tests are hard I question ha decent a tech he is, just saying all the best !
  16. Replies
    10
    Views
    3,254

    Had a carrier once with a sliver of the rubber...

    Had a carrier once with a sliver of the rubber cap from coil jammed in orfice figured it was from what ever they inject nitro into pushed it in to piping
  17. Replies
    33
    Views
    5,707

    I too would say secondary heat exchanger is toast...

    I too would say secondary heat exchanger is toast is furncae sloped back ? I have always tried to slope then slightly forward to help water drain out of secondary better and avoid it sitting in...
  18. This may be a silly question but why would you...

    This may be a silly question but why would you ever change a txv or do anything major to a system with out first cleaning a admittedly dirty condenser coil. Sounds as if the txv isnt set up...
  19. Replies
    12
    Views
    4,101

    Got to love customers being pro active and...

    Got to love customers being pro active and relizing their equipment is past its usable service life
  20. Replies
    40
    Views
    6,219

    Would this not close the txv ? Not open it as i...

    Would this not close the txv ? Not open it as i assume is intended.
  21. This may be a silly question is the heatexchanger...

    This may be a silly question is the heatexchanger ok as it could be leaking small amount of water into system but leak test on compressor replacement should rule this out
Results 1 to 21 of 21