https://www.automatedlogic.com ..... select Support, then Find a Dealer ......
Type: Posts; User: Balibe
https://www.automatedlogic.com ..... select Support, then Find a Dealer ......
Appears this is hitting way earlier than expected ...... the Comfort Controller (CC6400 & I/O) cannot be ordered after April 26,2024 and will be removed ordering system and be obsoleted ......
It may work but not legit ..... the USB-L is an after-market and not what Carrier provides with the legit product. The software is more than likely illegal to re-sell as it is proprietary software...
This program does not use the reschedule time as it never hits the ENDTASK, both steps just loop back to STEP ONE.
STEP TOP sets the defaults after a program first starts (power cycle or...
A DELAY is a variable in the program, separate from the reschedule rate. The DELAY will pause the program. The reschedule rate is started when the program reaches the END TASK line.
Have you...
The default is every 1 second unless someone changed it. Look for the following on the TASK line, the bolded blue number is the reschedule rate in seconds (search for reschrat in the manual) ...........
That is a VVT Monitor Stat and Bypass controller, probably GenIII but cant tell with the cover on. If there is a rotary dial (numbers and letters) under the cover near the display, it is GenII
It...
As stated earlier, replace the microblock ........
The do not wear out, they are upgraded with better ones .....
The forum started adding ads to sections? While I understand for non-members, why are members getting them when logged in?
+1 for Pi-Hole .........
..........870415
For a lack of an intelligent/technical terminology, I will go basic …..
With the ZS sensor and the sensor binder microblock they off-loaded the functions of the RS block to existing blocks and...
+1
That is just for the setpoint adjustment.
Local override is in the occupancy microblock. Fan adjustment will need to be added with an MSV microblock …..
If these are old microblocks,...
Glad it work out for ya, I am done and out .... good luck with it ......
No, they are not using the Niagara CCN driver. Trying to use the current i-Vu CCN devices for integration to N4.
The niagara ccn driver may have been the way to go, especially with the obsolete...
Looks like your issue is on the Tridium side, not on the Carrier side (if setup correctly). I tested on my test setup and it worked for me.
Keep in mind, the CCN Router was not designed for 3rd...
How are your integrating the schedules into Tridium??
Also to note & to check, two supervisors is a no-no. One will over-write the other. You may need to shutdown the i-Vu server as you have two...
Hmm, someone left the site using 65+ schedules after overlaying i-Vu. You may find different numbers being used on different floors or air sources.
VAV Terms defaults are 64, set the vav...
Schedule numbers are old and go back to 80/90's with BSIV & CView interfaces. Typically left at their default with i-Vu, 64 or below. i-Vu retains the schedule numbers as they are needed with the...
Input_Occupied is the occupancy status from the occupancy maintenance table, it is a status and not writable from i-Vu or bacnet.
There is no way to override/command an occupancy schedule in a CCN...
It should still scan the controller if it is a 38AP controller and generate a control program & graphic based on version 5. Read the first paragraph, it states this and may need to be...
It is not the PIC Type but the version of software in the PIC. It is a 38AP with version 6 software.
Below is a screenshot of a 48/50A, i-Vu shows the model number of 125AK-7. From the sal pdf a...
Check the version of the CCN Discovery SAL File in i-Vu (system options ==> update, then expand current libraries), the file is ivu-|version|-discovery-|file date|.sal. The current version is...
Is this a CCN site or an Open site with BACnet controllers?
If CCN, was it an upgrade from v4.0 to v6.0? Might explain the duplicates in i-Vu as the controllers were being upgraded/replaced in...
M.O.V. Training Services (Link) provides Level I/II certifications online .....
Believe they mean custom program modules you can export from CCT. These are custom regular/hybrid/modified modules that you can export and use/share in other programs. They are saved in the...
I do not, have only talked with them. I only found about them as Alps added their services to their catalog. We were looking to bid a project with 40 NAE's and over 1000 devices from Metasys to N4,...
There is a company that can take NAE databases and fully convert them to N4, they are Kander (Link). I have not used the them but have talked with them as we were looking to do the same thing,...
The FX-90 is available, orders opened up on 03/01 and shipping started today 03/18 .....
The FX-90 requires v14.13.2 (released 02/12) or higher, cannot go lower. FX-80 will be available thru...
Did they make a VMA2620? Typically the 2620 is a MS-FEC2620.
Are you using a One-to-One or a MESH application for the wireless sensors to the controllers?
Should of used the original program (not a new one) and updated in CCT to the latest, this would of retained all all SA devices in Define Hardware including the wireless ......
You did not mention wireless sensors in the original post. Since you updated the application to a higher version, did you update the Radio Firmware? This is a separate process under tools/truck...
ACI also has them, not sure if they are a replacement for you application ...... If not in their catalog, they can make most anything you need .....
https://www.workaci.com/search?keys=HAZARDOUS
I doubt a merger. Carrier acquired ALC in 2004 and based their entire control line on ALC controls, doubt they will be selling off ALC or the OEMCtrl division .....
You cannot modify a program with i-Vu, you need to use Snap. Carrier programming tools (TechTools) is totally separate, not included with an i-Vu purchase and not tied to the i-Vu licensing.
So...
The 1st generation of the FX-16 was not unloadable. Needs to be at least a 2nd generation, denoted by Rev A or Rev B on the controller. AFAIK it was a hardware change that made them unloadable,...
I just did 5 of them with the Trane Symbio app, it went very well too. Was easy to setup for BAS Control versus Stand-Alone with the app.
The thing I liked about these if the unit is not...
0 (zero) is also a valid MAC address on a MS/TP network for a device.
The newer Belimo actuator with the manual release is nice. It is bad because they machine riveted the actuator to plastic housing. So if the actuator is bad, need to order the actuator and housing....
You have mail .......
There is no work around that I am aware of since dealing with i-Vu since released. If created with Eikon, you cannot open with Snap. Carrier also has programs from the factory on VAV's, RTU's, etc...
What software version? If they are v1.5 or earlier, may need an update. v1.6 is the last series fan patch I can locate. There was a time clock issue causing controllers to lockup, believe it was...
Need the iTM BACnet Server Gateway Option (DCM014A51), not BACnet Client (DCM009A51) Option to export the devices to BACnet/IP. Once the gateway license is activated in the iTM, you will see an...
Your not blunt, I was thinking the same thing!! I just get tired of responding and ignore the posts.
CCT v10.3 is not free. The software will do you no good without the licensing to the...
Just did 12 new Trane rooftops into a Jace. The YHC's (036/060) with the RTRM and new BCI2-R used the IP address with a browser and the printer cable (no display) to configure. No need for the...
This works for me, I can change this setting for over 300 trends coming into the server from one Jace.
Agree with RC, I typically do them daily. Especially with multiple Jaces to the server,...
You can order them from Carrier with "-BNK" and the sensor will come with no logo or blank on the cover. I believe all can be ordered with -BNK but the VOC sensor.
FYI ..... not sure with ALC, but...
Don't think this has been noted ..... What version of CCT are you using? What package/build do you have installed for the CVM03050?
We never bought the MAP, have always used the LP-KIT204. I have downloaded over 75 F4-CVM03050 vav controllers with the LP-KIT204 with no issues, these were with firmware versions 9.0 and 10. Program...
This is what I am to understand from my support channel ......
The HostID remains with the SD Card, you will need a new license issued as the serial number of the Jace does not match the...
The HostID is tied to the SD Card, not the Jace8. The license attaches the HostID to the serial number to the Jace8.
If the Jace8 is dead, you should be able to pull the SD Card and install in a...
We have been using BASSG ..... Quick turn around and reasonably priced, saves me the time to create them myself ..... Talk to Alper (member here) or Ekim .......