Search:

Type: Posts; User: jayguy

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    4
    Views
    121

    There are some flow switch changes as well. If...

    There are some flow switch changes as well. If you have the Danfoss EEVs there is a software upgrade. There is also a processor software upgrade. If your unit was affected, it should have been...
  2. A large multitude of factors can damage a chiller...

    A large multitude of factors can damage a chiller long before an arbitrary date. Many of those items have nothing to do with whether the compressor is VFD driven or constant speed.
  3. 10% capacity on a fixed speed compressor uses...

    10% capacity on a fixed speed compressor uses significantly more energy than a VFD compressor at 10% capacity.
  4. Fancy! I only have the 435. It is sweet, though.

    Fancy! I only have the 435. It is sweet, though.
  5. Yep. I have seen this many times. The installing...

    Yep. I have seen this many times. The installing contractor puts in a resistor across 1&2 and then wonders why the unit won’t go into heat.

    by the way, these units can be configured a few hundred...
  6. Rogowski coils.

    Rogowski coils.
  7. you can not recalibrate the vane motor switch,...

    you can not recalibrate the vane motor switch, however, if the linkage isn't setup properly, the vanes may be fully closed, but the motor is not fully closed and the mechanical limits inside the...
  8. Replies
    15
    Views
    1,334

    How would you add refrigerant?

    How would you add refrigerant?
  9. Thread: Mixing of oils.

    by jayguy
    Replies
    14
    Views
    874

    The issue of “mixing oils” has nothing to do with...

    The issue of “mixing oils” has nothing to do with the oil. It has to do with converting from one refrigerant to another when the new refrigerant requires a different oil. The concern is if there is...
  10. Replies
    4
    Views
    307

    There can be many reasons that the next chiller...

    There can be many reasons that the next chiller starts even though the running chiller is not fully loaded. Such as inaccurate sensors, design issues, cold condenser water, etc.
  11. you can use an adapter like this:...

    you can use an adapter like this:
    https://www.fluke.com/en-us/product/accessories/adapters/fluke-pm9081
  12. Fluke 289: 0.001 mV to 1000 VDC and VAC 0.01 uA...

    Fluke 289:
    0.001 mV to 1000 VDC and VAC
    0.01 uA to 10 A AC and DC
    0.001 ohms to 500 Mohms
    temperature
    0.001 nF to 10 mF.

    no amp clamp though. I carry an add-on amp clamp from FP that goes to...
  13. Replies
    14
    Views
    1,048

    I have done this many times. However, I have them...

    I have done this many times. However, I have them manifolded together such that I push-pull liquid into 1 tank with the vapor going into the liquid port of another tank, etc and my recovery unit on...
  14. Replies
    11
    Views
    919

    Not replacing the valve plates means you will be...

    Not replacing the valve plates means you will be replacing the compressor. There isn’t much lubrication going on every 5 minutes with a 5 second run time. CYA and recommend valve plates.
  15. Replies
    13
    Views
    894

    Are your gages accurate?

    Are your gages accurate?
  16. Replies
    46
    Views
    2,817

    I have the ford 6 with eco-boost or some garbage....

    I have the ford 6 with eco-boost or some garbage. It struggles with the freeway on ramp. Iowa hills arent too bad so I don’t notice it there. I drive a lot of miles on the interstate so after I...
  17. Replies
    9
    Views
    593

    Unfortunately, the Dwyer U-tube 1227, set on an...

    Unfortunately, the Dwyer U-tube 1227, set on an incline still isn’t as accurate as the 922. And with the kit, it does much more than just gas pressures...and without running out of red dye or...
  18. Replies
    9
    Views
    593

    One of the things you will notice with it is the...

    One of the things you will notice with it is the temperature drift of the sensors. The sensors are very accurate but they drift a bit and you need to zero them out a bit more often than I like but I...
  19. Thread: Screw Vs Other

    by jayguy
    Replies
    5
    Views
    474

    I don’t know if there is anything vastly...

    I don’t know if there is anything vastly different other than the amount of oil it pumps. Do you have an issue or other reason in mind?
  20. Replies
    8
    Views
    1,407

    Is this on the 3630 board you upgraded to? You...

    Is this on the 3630 board you upgraded to? You should be able to get to all of the Sales order into unless you pressed the “finish setup” button.
  21. Replies
    8
    Views
    695

    I know that a little bit of oil is used to...

    I know that a little bit of oil is used to install York’s oil less chiller orings. But it is a very small amount. I would agree with the contaminated tank theory.
  22. Replies
    1
    Views
    259

    check your inbox. it is a large file so it may...

    check your inbox. it is a large file so it may not come through. they changed the model number from LCH to YCW so i may have some of the LCH stuff if you know what model number to look for.
  23. Yup

    Yup
  24. Replies
    10
    Views
    778

    Many but not all.

    Many but not all.
  25. Replies
    16
    Views
    1,831

    With the exception of the aforementioned issues,...

    With the exception of the aforementioned issues, it is a fairly clean install. The water heater pan needs replaced. Code may not allow for a copper gas line...this varies by jurisdiction but I would...
  26. Replies
    10
    Views
    778

    If i am not pulling the charge, I go by Evap...

    If i am not pulling the charge, I go by Evap approach and Discharge Superheat.
  27. Replies
    10
    Views
    778

    i haven't seen any large chillers that are...

    i haven't seen any large chillers that are charged to subcooling except for some air cooled models. The larger the chiller, it becomes obvious that more subcooling costs more money.

    Perhaps this...
  28. Replies
    30
    Views
    1,770

    jayguy1 said that. Totally different person.

    jayguy1 said that. Totally different person.
  29. Replies
    30
    Views
    1,770

    If there is a lot of oil in it, it shouldn’t take...

    If there is a lot of oil in it, it shouldn’t take too long!
  30. Replies
    30
    Views
    1,770

    Uhhhh, wait. Let me repost this advice from my...

    Uhhhh, wait. Let me repost this advice from my spam account.
  31. Replies
    30
    Views
    1,770

    Dump a bunch of cheap, liquid refrigerant in it...

    Dump a bunch of cheap, liquid refrigerant in it and use an infrared meter.
  32. Silver solder, duct tape and some paint.

    Silver solder, duct tape and some paint.
  33. Replies
    23
    Views
    4,529

    I have found that, even if the new equipment is...

    I have found that, even if the new equipment is similar to the old equipment the or the new problem is similar to the old problem, there are enough differences to confuse the 2 issues. Starting a new...
  34. Replies
    8
    Views
    833

    As for your ground fault issue, Danfoss did have...

    As for your ground fault issue, Danfoss did have some ribbon cable failures that would cause that.

    as for your overvoltage, your meter isnt deigned to handle the ACTUAL voltage going to the motor....
  35. Replies
    13
    Views
    1,037

    The nickel fell off?

    The nickel fell off?
  36. Replies
    14
    Views
    2,039

    These new designs sure are space saving.

    These new designs sure are space saving.
  37. Do you have a better picture of wire tie on the...

    Do you have a better picture of wire tie on the left? It looks tight. If it’s tight while the tubes are crushed, it could have been this way from the factory.
  38. Well, it ran fine for 6-ish years. So this...

    Well, it ran fine for 6-ish years. So this happened recently. My money is also on a water issue but I wouldn’t know what issue. Logically, the water crushed the tubes when you pulled it into a...
  39. While I don’t agree with all of your tips, I am...

    While I don’t agree with all of your tips, I am glad you got it fixed.
  40. Replies
    18
    Views
    995

    So you are chastising us for not reading your...

    So you are chastising us for not reading your description and then the rest of your post was new info.

    i’m out.
  41. Replies
    36
    Views
    1,765

    BluVac Pro. Don’t be tempted to go cheap. Going...

    BluVac Pro. Don’t be tempted to go cheap. Going cheap is so expensive these days.
  42. Replies
    18
    Views
    995

    Classic “hot box” pull down scenario. The design...

    Classic “hot box” pull down scenario. The design is cold and the compressor design is for a small amount of refrigerant flow. Now that it is warm, the compressor can pump MUCH more refrigerant than...
  43. Replies
    4
    Views
    708

    I have used them before. They can work very well....

    I have used them before. They can work very well. I usually use a pressure drop method but it certainly has it limitations.
  44. Replies
    21
    Views
    1,953

    In your particular case, M/S are probably not...

    In your particular case, M/S are probably not necessary. Adding more information helps to avoid the questions that are important. In more difficult or technical cases, the model AND serial numbers...
  45. Replies
    11
    Views
    442

    Ok...so that’s good. Still, if the water flow is...

    Ok...so that’s good. Still, if the water flow is low enough, then small movements in the PRV will cause big changes in the chilled water flow. Also consider that the PRV position sensor is kind of...
  46. Replies
    52
    Views
    2,675

    Low airflow is one of the most common reasons for...

    Low airflow is one of the most common reasons for low suction pressure (like a dirty air filter). Increasing airflow will not help with an oversized unit but decreasing the airflow will make the...
  47. Replies
    11
    Views
    442

    so...what is common between both chillers? i...

    so...what is common between both chillers? i suspect tube fouling on the chilled water side. i just finished troubleshooting a job that had a 4.5 psid across the evaporator (nearly exactly design)...
  48. Replies
    52
    Views
    2,675

    i seriously question your advice.

    i seriously question your advice.
  49. Replies
    7
    Views
    7,297

    I know it seems dumb, but start a new thread for...

    I know it seems dumb, but start a new thread for your issue. It helps keep things clean and then symptoms and fixes don’t get mixed between the different machines.
  50. Replies
    52
    Views
    2,675

    And the guy before that looked at the “12” and...

    And the guy before that looked at the “12” and thought it was 12 tons instead of 120,000!
Results 1 to 50 of 1000
Page 1 of 20 1 2 3 4