Does anyone have experience with troubleshooting these???? I have one that after power reset will come on run normally for 10 mins then completely shuts down.I contacted tech support and they said...
Type: Posts; User: dodger454
Does anyone have experience with troubleshooting these???? I have one that after power reset will come on run normally for 10 mins then completely shuts down.I contacted tech support and they said...
If the NAE's are Rev 5.2 or higher go to JCI website and download the launcher program.It's free and the java is built in to the program.
Something doesn't sound right.If JCI installed the job with a Metasys ADS/ADX server then they should have left the software,and the customer could have added/deleted software. Coming back after 5...
What Revision of Metasys are you dealing with?
Got my new JCI win 7 pc and can't get V-tools SCT to work can anyone help??
I don't do residential work but a friend of mine bought a used AM STD heatpump.He asked me to do the control wiring hookup.There are no wiring diagrams that aren't badly faded and this unit uses wire...
See if you can move over to the service side of JCI.But if you looking to be around women good luck,you will spend most of your time behind the scenes with the building maintenance people.On the...
Steps to load UNT configuration into VAV controller.
1. the UNT xxx.cfg file in Notepad. (xxx = filename)
2. Change the following:
a. Device Group: UNT to VAV
b. Device Name: UNTxxx-x to VAVxxx-x...
Haven't done this in a while,I think You need to save file as a UNT.Then change the .PRN file back to VAV.It's a pain.I have a file somewhere on the exact steps.Let you know when I find it.
LU 449
There has been rumor of a N2 FEC for over a year but nothing yet,and rumors of the VMA 1600 being configured for N2,again nothing yet.One thing to keep in mind if your facility upgrades to Windows 7 ...
Check the firmware code, HVAC Pro-Action-controller information.If it's a 8.08B it should be C05,If it's C02 or lower download the C05 code.This must be done thru the N2 bus.Also make sure you upload...
2 ways to reset PID,upload controller and then download it.That resets the PID,or change the adaptive tuning to manual then change it back to adaptive tuning.CCT 5.0 and up have a network input reset...
WARNING !!
This setting should only be entered into the gx9100.ini file if you intend using
the password feature. If a DX controller has been password protected and the
password has been mislaid...
I believe they were reconditioned less than 5 yrs ago. Make offer
he ability to set a password in the DX via the GX9100 is dependent on
having the following line in the [Settings] section of the gx9100.ini file:
PasswordEnable=Yes
The NCE is the eventual replacement for the DX-9100
Working on a system that uses 2 ASDI integrators that feed into a TAC UNC-520 integrator that are IP bacnet to Metasys.One works the other one does not.The bus voltages are the same and all devices...
There's some great customer service.Mr Customer you need to replace this contoller because I have no idea how to upgrade it.
use the "port dump" to get your IP address,use a switch not a crossover,and read all instructions in the LIT then try again.Also if you are trying to upgrade a NAE 55 make sure it is a NAE 55xx-1, a...
Metasys 5.0 is rumored to be compatible with Windows 7
blackbelt unless you are a JCI employee I don't think you can.It has to be dowloaded from the JCI portal and each JCI Branch must license it.
GX-9100 is in M-Tools WMX-9100 is not
I'm pretty sure theWGX is a propriatory JCI program.It comes from JCI Italy.
Save the file as a UNT then edit the config file using note pad and change the UNT to a VAV and save file using notepad.Download the controller with the edited file and then upload and commission.Not...
I agree that no matter which side Control techs come from there are scrubs on both sides.I am bias to the mechanical side because a good HVAC mechanic knows why things operate they way they do...
Some of the larger controls companys are finding its easier to teach us "freon jocks" the digital controls end of the business,than to teach the computer jocks HVAC.We actually know why things do...
I use it all the time.Great way to trouble shoot DX-9100.I think it's propriatary JCI only.