Search:

858477

Here is how the intake and exhaust pipes terminate above the roof.

The carrier trap and connection to the drain line might be overkill . Perhaps a simpler solution is to drill a small hole and/or plug it. It is not likely that it will ever be filled with water as...

This, I think we can say it aloud.. A small hole on that trap at its bottom and close it off with a grommet. Check now and then if there is any fluid or debris collecting there.

Exactly what I was thinking too.. great suggestion.

Installer accepted mistake and fixed it. I am including additional photos.

858297
858299
858301

Question to you all: In the Bryant setup above, can the Blower and Combustion chamber sections be (swapped locations) such as by installing the furnace upside down(rotate on an axis along the like of...

The outside Unit.. still work in progress, power connections yet to be made as well as insulation on the lineset. Prior existing copper line set was used. Compared to the prior York installation, I...

Use of Primer on the pipes.

858255858257

"Condensate needs to be able to flow back to the furnace unobstructed, and with that reducer in that position, it can't. So at a minimum tell him to redo that." Yes, I will.
"As far as the pipes...

Observing the current Bryant installation and previous York installation, it appears to me the current Bryant installer made a mistake and swapped the exhaust and intake sections. That might reduce...

This was the original YORK Affinity series that was replaced. Note: the location of the exhaust is on the right side. I miss how nicely the pipes were routed. But they had the luxury of taking it...

To the installer's credit, he too made the same comment when I asked him that I installed the water heater myself and his opinion on the work. I will get it fixed by replacing it with CPVC as you...

<>

The installer just finished setting this up. He has not powered on yet because it got very late on saturday and he will come back Monday. Any opinion on the ductwork? It has been bothering me that...

Thank you. I bought the Thermostat on offerup so I dont think there would be warranty. I will register on the Bryant site, since the Bryant heat pump and furnace are procured and installed by the...

https://drive.google.com/file/d/1AVTx663qDjBS6KHjCfYuDOHm-k1eeJeG/view?usp=sharing857473

Its not a DIY project. I have an installer scheduled to install it next week.https://drive.google.com/file/d/1AVTx663qDjBS6KHjCfYuDOHm-k1eeJeG/view?usp=sharing

Yes, it is touchscreen
What do you mean ICP is different?
If I use the carrier infinity thermostat on Bryant equipment, should I register at the carrier site or Bryant site?

Question re: compatibility,
Can a Carrier Infinity thermostat (SYSTXCCWIC01-B) be used to control and communicate with Bryant evolution heat pump (284anv) and gas furnace(986t)?
When registering...

hi, I have a Carrier infinity thermostat and am planning to use it to control a yet to be installed, Bryant evolution heat pump and furnace.

I have a few questions.

Where do I register the...

I could never get more than 5-7 degrees of cooling in my system past 17years, did not bother trying to figure out why and just accepted it
heat pump has failed and i started looking at replacement...

I have decided to get rid of a 17y old York Affinity system with a failed compressor at my house and been talking to an installer. I have a functioning 98V York Affinity gas furnace. Installer is...

I will measure tomorrow and post here, the compressor amps.

what are possible reasons?

hi all, I am a Home owner with a R410A based York Affinity series heat pump issue.
Symptoms are: Air coming out of vents is ambient temperature, whether in cooling or heating mode. Compressor...

I am here 16years later! how are you all doing?. Hope lifes been kind to you. It certainly has been to me, Thank God.. I am here for a quick update.

My aging Heat pump stopped working. It blows...

bingo! you are right on the dot.

Installer came by today and showed me that the FFuel jumper was at AH position. He changed it to Furnace and the problem was solved.

Hats off to you for your...

It is tax season and I was busy trying to understand how much of tax credit I would qualify for.

My equipment is:
York Affinity series 8T (4ton) YZE 048 heat pump and Indoor Coil G4FD060H24T a...

<snip>

I called and talked to my installer today. He clarified that there is no bonnet sensor installed. I asked him why he did not install one and to that he said that my equipment is so advanced (please...

I suspect that I may have the bonnet sensor, here is why.
Last time I called the installer to swing by and fix the problem, he came over and changed the temperature setting on the heat pump out door...

thanks for your replies. I should have made it clear though, as it doesnt answer my question.

from your email, I see two approaches

Approach 1: "It can be wired to run the furnace only if the...

Which of the two approaches you list above is preferred? [for Seattle area, if Geography should matter]

How does the choice impact things that matter to me, such as energy bill, longevity of the...

Yes, no matter how cold it is outside, the furnace does not start. Heat pump keeps chugging away.. only way I can put an end to the Heat pumps misery is by clicking on "emergency heat" which turns on...

<snip>

My system seems to work fine as a stand alone Heat pump (both heat and a/c). If I have to switch to furnace, I need to use the touch pad control and set it to Emergency heat.

The installer came by...

As we head close to a date with Uncle Sam, I would like to know if I am eligible for a tax credit, Equipment I have is: York Affinity series 8T (4ton) YZE 048 heat pump and Indoor Coil G4FD060H24T a...

I own an Affinity heatpump installed a year ago in the Seattle area. Worked like a charm. Only issue i have is that installation is a bit complex and my installer did not install properly the...

Its been nearly 8months with the install, overall I am very satisfied with the York affinity series. Have one observation though..

when temperatures fall really low (I mean in the twenties) in...

It was just a furnace that I had earlier.

It was 80% single stage Payne rated for 80,000BTU. A pretty basic furnace. I knew I wanted A/C but wasnt so sure about replacing the furnace because of...

You wrote: What size was the A/C the builder installed.


As mentioned it is a heat pump or a reversible A/C

rated at 4tonnes

You wrote: "I don't like the idea of a transition to make an incorrect size evap coil to fit on a new installation. York certainly has a matching and correctly sized evap coil to fit properly with...

I will check with them if they installed a bonnet sensor. I looked at the invoice and there isnt a separate line item for that, possible they did not install it. Also based on your explanation of...

I live in the Seattle area so it doesnt snow here so I am thinking I dont need pumpups. The installer did install a thermostat near the outdoor unit and because of sunlight directly falling on it I...

the installer said he couldnt find a 21 inch coil that would do justification to the heat pump YZE 048.. the coil he installed apparently is large and sized right but didnt match it in terms of...

Last month I had installed York Affinity series 8T (4ton) YZE 048 heat pump and Indoor Coil G4FD060H24T a 9v backup gas furnace ( PV9C16N080DH11). Both are variable speed and I really like the way...