Search:

I can see the bungee cord. I can't see myself trusting that cord or what it's attached to though. I like a good rope to hang from. If nothing is close I get another rope to reach something :)

Touch pad is another sticky wicket. Water pump impellers were weak early on but I think they changed suppliers.

https://youtu.be/iUODdPpnxcA

Cinco

813255

Sounds like a harvest issue. Also check water curtain switch alignment.

They are curious.

I've read about others adding N2 to systems just to see what happens.

There might be some systems that will trap all of the non-condensables in the highside but I'd say most typical systems would see a higher suction superheat due to the non-condensables traveling with...

Ring is a door bell with a camera. It's supposed to be touched. Security camera Ring or otherwise be should be out of reach. If someone grabs the Ring doorbell Ring will replace it.

High suction superheat

Gooru is full of Pooru

The old mechanical stat freezers were pretty much the same with a wide diff.

Harvest starts around 18 mins in.
2.5 mins after that vacuum seal is completely gone from behind the ice. Takes another 30 seconds to slowly drop after that.

70°/50° book time for this machine is...

Is this your machine and the thick ice?

https://youtu.be/k9mfJtQf48w

Not funing about the pump. Let me find the video and post.

You have the tools.
You have the book.
What's the deal milking this job?
You need more time?
In house guy?
Seriously want someone to wave a magic want?

I've been pretty nice. Don't know why he seems to be getting amped up.

Ok I see. Your compressor is weak.
Get a bigger machine.
Prove me wrong.
Your video doesn't show ice like the pics.
The pics are probably after a double batch because of the harvest issue.

Do you have the test procedure for the floats? Yea I know they are new but they need to be tested with tools. The board has lights too. You have the service book?

I think when he reads something his brain fills in what he is thinking. Probably the same if he was talking to tech support. He's not hearing it either way.

Something would be out of wack if the other two were needed but it's an option.

That's not a quote and you are posting what you are hearing in your head when you read my post.
I don't get a week to fix one ice machine so there is plenty of time to post garbage to your thread...

Are you a tech?
Take a step back to the video please.

Explain your long harvest.

Yea maybe the ice is a little thick but didn't look to bad.
You did not provide bridge thickness or total...

Would like to see his level, water pressure gauge and DMM too.
If you need them they are all out in the truck :)

Can you quote my posts where you misinterpreted their meaning please?

Dude the harvest float is fixed...
Doesn't move from the back mounting position.

Ice thickness is controlled by the front float. The high it is mounted more water is allowed to fill the trough....

Evidently it's on the lowest of low ice thickness settings since his ice is thin.

Your ice thickness float is on the very high or very low nub on the left hand side V

pfft
tisk risk

Nothing is supposed to go there. Those are for decoration on a NEO
When you use that water...

What's your water pressure. If too high you'll overfill. The guy you talked to probably wasn't on the design team or around back then either. The guy who was on the team isn't even working there...

Do you have a level and a DMM

Full thick slab is not low on charge.

Take the water trough out and have a look. Harvest float goes on the back two nubs where the stainless hook sits right over the water trough lip. There are two more front left corner you can hang the...

Yes. I saw a long freeze and long harvest.
You can adjust ice bridge by moving the front float lower. There is another lower and higher setting around the left side of needed. If the machine isn't...

Weak compressor. Get a bigger one this time.

So this may be a myth. G5 is listed at 10 Amp and Fieldpiece/Inficon 12 Amp

I haven't had any starting or voltage drop issues with my G5 using a cord. The way the compressor works is low starting...

Wow
The other side have a relative who was working for nothing?

A printed one would probably be a waste of material and time.

The water curtain is vacuum formed plastic. No computer or expensive printer needed. Just a warm piece of plastic sucked over a mold.

They make them a lot better now. They sure don't break like...

Dirty water level probe

Those are vacuum formed.

Had two coolers with those little timers at a school science lab this week both +90°

One was empty one was full of body parts.

The instructor said she knew there was a problem because she...

I used to like getting new vans. The older I get the more I hate when the time comes to move all the junk over.

PHM is this a van you work out of?

He did say started but I doubt he ment that. Also no voltage measurement with that amp draw.

That's too high to be inrush imo.
That's why I said short in the first place ;)

Not sure when inrush can be lower than LRA...
Is there a different meaning for inrush besides LRA + the...

Inrush is higher than LRA.
Not the same thing.

Shorted out

That nut looks too thin for brass

Three AA batteries instead of one 9V