Search:

Type: Posts; User: corny

Page 1 of 20 1 2 3 4

Search: Search took 0.45 seconds.

  1. Replies
    2
    Views
    408

    I would enjoy doing sheetmetal work for a small...

    I would enjoy doing sheetmetal work for a small shop who actually wanted to make decent ductwork but from what I have seen of residential light commercial the last 10 years is... they just aint going...
  2. Thread: Wire Diagram App

    by corny
    Replies
    12
    Views
    945

    Remember the old Forest Mims... think that is...

    Remember the old Forest Mims... think that is correct... books. His drawings were all freehand and looked good. Those drawings got a lot of people started off into electronics.
  3. Replies
    23
    Views
    933

    Skills..... not paying for skills anymore........

    Skills..... not paying for skills anymore..... duct monkeys... duct gas flex runners......
  4. Replies
    23
    Views
    933

    I see a lot of problems with flex returns. ...

    I see a lot of problems with flex returns. Twisted... or bunched up making 90 degree... or more... turns.

    Flex.. its bad.... but its here to stay. Some folks do it right and it works.. others...
  5. Thread: Shoe Covers

    by corny
    Replies
    17
    Views
    562

    We use criti clean shoe covers. Pretty heavy duty...

    We use criti clean shoe covers. Pretty heavy duty plastic. I wear them a lot outside too in grass.. mulch.... and I also wear them on black rubber roofs
  6. Replies
    3
    Views
    738

    I would check the system out in person.

    I would check the system out in person.
  7. Prob a store owner.... foreign store owner.

    Prob a store owner.... foreign store owner.
  8. Replies
    29
    Views
    820

    Got a late 70s carrier watersource with the orig...

    Got a late 70s carrier watersource with the orig run cap for the comp. its huge. I actually checked it a few years ago and it was like 36 uf or something.

    I think everything is orginal in that...
  9. Replies
    16
    Views
    1,019

    Whatever Became Of The I Manifold ???

    Just wondering if folks still use them.
  10. Replies
    13
    Views
    833

    Had a leak today on a rev valve pilot tube where...

    Had a leak today on a rev valve pilot tube where it goes into a stub. Inficon going off anywhere near the unit..... soap bubbles not showing anything..... cause the leak was blowing hard enough to...
  11. Thread: not normal.

    by corny
    Replies
    8
    Views
    977

    Years ago when people were still doing full duct...

    Years ago when people were still doing full duct installs in homes with ceiling heat... used to get bit quite a bit touching the cabinets.

    Used to go up to them and slap them...... still do on...
  12. Replies
    5
    Views
    689

    Just Dont Understand... But I Do...

    Call today. Woman has had two people out in a matter of weeks. Transformer keeps burning up. Neither person bothered to find out why. First one... they get old and worn out... second... could be bad...
  13. Replies
    13
    Views
    833

    I use my ultrasonic mainly in condensers......

    I use my ultrasonic mainly in condensers... condensers where the refrigerant leak detector is going off anywhere near the unit.

    In evaps..... if my refrig leak detector goes off in the unit........
  14. Thread: Gloopman…..

    by corny
    Replies
    19
    Views
    2,183

    and what are wop posters ???

    and what are wop posters ???
  15. Thread: Gloopman…..

    by corny
    Replies
    19
    Views
    2,183

    What does wos mean ???

    What does wos mean ???
  16. Replies
    12
    Views
    768

    They should be properly trained to install...

    They should be properly trained to install whatever is being installed... complicated or not. If not then SOMEONE... knowledgeable should be sent out to set everything up correctly and test the...
  17. Thats not a hack... thats ingenuity.

    Thats not a hack... thats ingenuity.
  18. Replies
    14
    Views
    618

    Place that does leather work... like some shoe...

    Place that does leather work... like some shoe shops..... they might tackle it.
  19. Replies
    60
    Views
    2,130

    Back years ago I did a lot of gas piping. I wore...

    Back years ago I did a lot of gas piping. I wore bibs whenever doing piping work. protected my shirt from oil grease and dirt.... I just loved em for piping.

    I wear uniform pants now.... and wear...
Results 1 to 19 of 1000
Page 1 of 20 1 2 3 4