Search:

Type: Posts; User: Stoichiometric

Search: Search took 0.02 seconds.

  1. Also , I would try to convince the facility to...

    Also , I would try to convince the facility to fix the steam traps , or the new pump will die from the same thing the old one did.

    Cavitation, from pumping too hot of condensate .
  2. Up ,then over ,then down close to floor. Like a...

    Up ,then over ,then down close to floor. Like a upside down u.

    Do not p-trap it.

    That vent is the air vent for the system, if trapped, the air cant get out.

    Someone put those p traps in...
  3. Replies
    21
    Views
    934

    Pretty common occurence here, get a bunch of...

    Pretty common occurence here, get a bunch of calls beginning of every heating season.

    White silky substance behind the orifice.

    Only happens on mobile home furnace with one orifice,

    Never...
  4. Replies
    21
    Views
    934

    Spider web in orifice, happens all the time...

    Spider web in orifice, happens all the time around here on mobile homes.
  5. Replies
    4
    Views
    419

    Is this steam or water , assuming steam due to...

    Is this steam or water , assuming steam due to tds and ph monitoring.

    What does the near boiler piping look like.

    Is there some large load that picks up at certain times when it trips out?...
  6. Replies
    26
    Views
    1,461

    Surprised I'm the only one with justin work...

    Surprised I'm the only one with justin work boots.

    Made in usa, and smooth sole so can wipe off easy.

    My very first boss in this trade Would send guys home or to the store , or anywhere , but...
  7. Replies
    20
    Views
    1,904

    Very , well, creative I guess. What's up with...

    Very , well, creative I guess.

    What's up with your truck antenna, lol
  8. Replies
    10
    Views
    629

    Unhook all stat wires , see what happens. ...

    Unhook all stat wires , see what happens.

    Might be pinched somewhere
  9. Might want to double check the furnace sizing ,...

    Might want to double check the furnace sizing , possibly running too short of heating cycles, not allowing the flue to heat up enough to melt ice.
  10. Replies
    2
    Views
    283

    Have seen lots of steam wall radiators and fin...

    Have seen lots of steam wall radiators and fin tubes up high in old schools.

    more than likely it was in service before the drop ceiling was installed and now is abandoned in place
  11. Replies
    21
    Views
    1,583

    Electricians pouch with belt, holds all tools for...

    Electricians pouch with belt, holds all tools for 99% of service calls and can sling over shoulder for easy carry or use belt when when working on ladders. After 20 years I finally have the tool...
  12. Still permitted by NEC . Circuits must be...

    Still permitted by NEC .

    Circuits must be labeled as such

    Some municipalities have banned the practice
  13. Replies
    3
    Views
    403

    Search on heating help.com , CAC/BDP 3 WIRE PILOT...

    Search on heating help.com , CAC/BDP 3 WIRE PILOT TROUBLESHOOTING.

    It is the best theory of operation I have ever gotten
  14. Replies
    14
    Views
    1,453

    Looks good , I bend and swage everything also,...

    Looks good , I bend and swage everything also, saves lots $$$
  15. We , my family, use a HSA health savings account...

    We , my family, use a HSA health savings account .

    You save money (nontaxable) in the special account and pay doctor directly.

    Not ideal for bad injuries/large Bill's, but has worked for us.
    ...
  16. I stand corrected, upon some research i see...

    I stand corrected, upon some research i see special oil.

    I have only threaded a few pieces, used rigid dark oil. Seemed to work ok
  17. Replies
    9
    Views
    1,083

    Yellow jacket with the reverse kit, which had to...

    Yellow jacket with the reverse kit, which had to buy seperate.

    And the spin tool swageing set.

    Have saved me so much money its almost unbelievable
  18. Little late, but I just got the milwaukee fork...

    Little late, but I just got the milwaukee fork meter. Love it
  19. EDIT: Will thread with regular threading oil. ...

    EDIT: Will thread with regular threading oil.

    Use the noalox during assembly of joints , instead of pipe dope
  20. The noalox will stop corrosion and Allow...

    The noalox will stop corrosion and Allow disassembly, it is almost like never seaze
  21. Replies
    3
    Views
    1,053

    Curb adapter? Those cost too much, watch this. ...

    Curb adapter? Those cost too much, watch this.

    Been there for a while tho
  22. I dont have the model number , but it was just...

    I dont have the model number , but it was just the lowest end 80%. It had the ecm motor since there out of the psc models now.

    I hope I never see one again, lol
  23. Goodman gets my vote , put in an downflow 80% the...

    Goodman gets my vote , put in an downflow 80% the other day and blew the low voltage fuse ( rookie mistake I know).

    It took half an hour to disassemble everything and pry the inner door loose due...
  24. Replies
    11
    Views
    840

    We had a nest also low voltage on yellow ,...

    We had a nest also low voltage on yellow , chattering contacter. Oddly it was intermittent problem.

    Nee pro 1 stat all good
  25. Replies
    28
    Views
    2,323

    G1 here, not the fastest out there, but on...

    G1 here, not the fastest out there, but on residential systems works just fine, over 5 years old , not one problem
  26. Common neutrals are technically allowed but must...

    Common neutrals are technically allowed but must be fed from separate phases to eliminate over loading the nuetral.

    Not a real good idea though, as a loose nuetral will cause high voltage on one...
  27. Replies
    14
    Views
    863

    Coleman's uv lights also state " ozone free" ...

    Coleman's uv lights also state " ozone free"

    Good info r600 , I didnt know any uv could produce ozone
  28. Carrier. ( climatemaster) board out after 3 months

    Installed a 2010 year climatmaster geo in my house and circuit board failed in 3 months ( no signal being sent to blower).

    This is a new unit I bought from my supply house in 2014 real cheap...
  29. Replies
    11
    Views
    667

    I second the load calc, i cool my 1200 sq ft...

    I second the load calc, i cool my 1200 sq ft house with 2tons , and it has short cycles on all but the hottest days ( 95+)
  30. Differential , if everything is clear , I suspect...

    Differential , if everything is clear , I suspect partially plugged/clogged secondary
  31. 17 to be exact, the original board seemed to be...

    17 to be exact, the original board seemed to be adjusting the warmup time by a few seconds each time.

    I thought that was normal for older trane/as which is why I didnt recognize at first.
    ...
  32. Replaced circuit board and igniter under advice...

    Replaced circuit board and igniter under advice from my AS service rep.

    Problem solved.

    Seems as though igniter warmup timing had shortened somehow(bad board).

    Thank u again for the help....
  33. Thank you all for the replies,. I did play...

    Thank you all for the replies,.

    I did play with the igniter position with different igniters.

    I have checked checked and adjusted the gas pressure.

    I will check the orifices with proper bit....
  34. American standard not lighting all the time

    Hi all, long time lurker first time posting.

    Have an aux080r942v2 that has the update kit installed. New board, inducer, harness.

    Replace igniter 3 years ago with a hot rod , all good until...
Results 1 to 34 of 34