Search:

This

Now just because they're all in the same mode doesn't mean they will all be heating or cooling at the same time, but it does mean they won't be fighting each other

Having similar issues with a 2006 vintage MP581, too old to upgrade the firmware, Jace can read points from the MP but the MP won't read networked points from the Jace even though I can see the value...

Hey thanks for posting this, this is at least the third time i've downloaded this link smh

Typical of Trane unfortunately, part of the reason why many customers are leaving them behind

Maybe you can find a local guy that's former trane that can help you out

If not, I travel but it...

I like that they used EMT on the line voltage and that they installed the LL drier inside near the metering device, don't like the condensate drain running in front of the water heater or being...

If anyone is in need of an HVAC master in any of the juristictions listed above PM and we'll talk.

If it has an RTRM board then it has Reliatel controls and doesn't require a CTI board. Reliatel control boards have "Trane" terminals 1-12 or so as well as "conventional" terminals R-G-Y-W etc...

Not really, you can only put out what you get in. The maximum differential you can expect between a pump supply and return is about 30 psi at sea level. Why? Because you add the 14.7 on the back end...

Yes they sell them, I'll find the part # when I swing past the office later today

If you've never done it before I would hire Trane to do the entire job, you'll be happy you did.

What boards do you need?

There are different versions of TU as well. You'll need either the full version (which is Trane only) or the chiller version (which is also Trane only) :Faint::gah:

As much as I've ever known about how Reliatel works is this;

Each control scheme has a priority with 24v t-stat control being the lowest, next being Trane t-stat vdc control and the highest...

Rover is never going to read your UPCM, you'll need to go into a bit more detail about your problem and would probably be better served if you started a new thread.

Eh, I don't have a lot of experience outside of Trane, Tridium and KMC so I'd have to say Trane's UC400 is pretty crappy because they fail like 95 going North and Trane's AH541 sucked as well. ...

It's a MOD02085 if anyone ever needs it. That's for the plastic cover-BTW

Kind of straight forward question like the title says, does anyone know the part number or have the serial number of a Trane ZN511? I need to order a replacement.

Thanks,

The only way I know to have the BCU use Bacnet/IP and have the PC be connected to your ISP is to purchase two static IP's from your ISP, one for the PC and one for the BCU. This way they'll be on the...

I don't know what Version of Summit you're running but I've only seen this problem with v.17 and Windows 7 or higher. You must add the latest service packs to allow ethernet to work with Win 7 or...

It depends on how Summit connects to the workstation. If Summit uses a simple Ethernet connection then you should be able to use DHCP to connect to your ISP and ethernet to connect to the BCU. If the...

Trane VAV's (or any VAV that I'm aware of for that matter) cannot control humidity. Humidity control and discharge air reheat must be accomplished at the air mover (AHU, RTU, SCU, whatever).

The...

.....um, I could be wrong but I thing q-tip was agreeing with you and directing his statement "Yup, read above..." to the OP suggesting that he follow your advice.

Again, I could be wrong but...

You'll still need Tracer TU to enable the write points you want to control. You'll be able to pull them in and you can attempt to write to them, but the RTU won't respond to your commands until the...

I realize this is an old thread, but wanted to say "thanks" as this thread just helped me tremendously.

As the others have mentioned, you shouldn't need Trane for anything UNTIL 10% of your UC400's fail within the first year as has happened to me on every single stinkin' UC400 job I have ever done. If...

Most of the time Trane will not reset the Auth code unless there has been some sort of failure on the original PC the software was installed on. If you simply want to use Summit on a different PC...

If you decide to use the conventional terminals keep in mind that the BCI takes priority of the trane sensor terminals and the trane terminals take priority over the conventional terminals so the BCI...

I think it would be good to know if this is a factory installation or a retrofit. If this is a factory AHU/RTU then there should be a predetermined landing point for smoke.

what panel is on that chiller? I'm not sure there is a BACnet retrofit available for chillers that old.

I have several VFD's out there that are being controlled via 2-wire comm and haven't had any problems with them at all, but there's still that part of me that prefers hard wired control.

Put a temp sensor in the return in you don't have one in the space and jack you daytime warm-up and morning warm up settings to 80 or so. I assume you have heat in the RTU?

Make triple sure that...

And yes they are Danfoss drives with Tranes name on them.

I have done a few of these but I remember installing BACnet cards because they originally shipped with LON cards and we had to get BACnet cards overnighted. Set-up was simple however and they worked...

IP wouldn't be tough if you have Summit. You would definitely need a hi cap card and reference all the info you would want to expose as BI, BO, AI's and AO's. If you have Summit
it would be a ton...

did you guys ever get this one figured out? I'm having a similar issue except the Corel controller doesn't seem to take the start/stop command at all, but I get temps etc at my front end.

The BMTX BCU is capable of communicating to the UCP 1 and/or the UCP 695 panels. The BCU must be 2007 or later and have
the latest firmware. I've wired up quite a few of them.

connect to the BCU with you Tracer Summit software and choose "set-up" then scroll down to "custom programming". a window will pop up, close it and choose "program" at the top of the screen, then...

I'm still trying to figure this one out. I think it may be a problem with my PC specifically because I installed TU on a desktop that had basically the same config as my labtop and TU starts on the...

Anyone had issues with TU starting since the latest Java updates?

I'm running Windows 7 and the only changes that have been made to my laptop since the last time I used TU
were the Java updates...

You could have Trane replace the Tracer 100i panel with a BCU relatively easily and would maybe cost 15k including a workstation and graphics. Having everything replaced with new controls would cost...

what board is in the unit? post a pic if you're not sure.

I work at a zoo that's controlled by Tracer Summit, but it's actually a High School.

I downloaded this, thanks Lunchbox

I would try removing all override control except for heating/cooling setpoints and occupancy.

Welcome aboard or to-the-board rather.

I really don't have much to offer other than to say that I would think that it shouldn't matter where on the comm link the devices reside just as long as...

They're usually included in Rover service packs.

I don't see the point in operating the drives in bypass. If the towers are in an industrial/process application in which the cooling systems are always close to or at full load that still doesn't...

The part number is SFT1002 if I remember correctly. Try Trane parts with that part number.

emergency shutdown is used for the fire alarm in most applications. you want remote shutdown and it's on the LVTB or low voltage terminal board. there's a metal factory jumper in place on the...

Thanks, Joey.