Search:

I am looking for a good unitary/heavy tech and an apprentice. I also have a need for a seasoned service salesman/saleswoman with controls experience.

Dewey

Has anyone seen a failure in the static pressure sensor? I have 2 units that drop the pressure after about 3 minutes of operation. I have replaced the transducer and same think on both. I have...

Does anyone have a relay board. I will take a complete CCP-III if it has the optional relay board.

Guys, I need to know where (or even if) I can get a replacement Allen Bradley VFD for a smaller chiller. Someone let the smoke out of this one.

I am the Service Branch Manager for Heat Transfer Solutions (A Daikin Rep) for Central Texas. I have openings for both my Austin and San Antonio Offices. I am "NOT" looking for entry level people. I...

You and I seen like 2 peas in a pod! I am actually about to sell my Viking for a 182! Please pass the word around. I am not looking for entry level people. I am looking for a key guy and it will come...

Compensation is what anyone negotiates. I have always made way more than most because I go in with what was offered and proved my worth. You are correct, everyone worth having has a job. How about...

Guys, I have over 40 years in the industry, with most of my career as Team Leader for both Carrier and Trane Factory Support. I recently took over as Branch Service Manager for HTS Central Texas. I...

804557I had a chiller shorting contactor weld and the mechanical interlock failed. Blink Blink Bang. The starter is beyond repair. I have an identical one next to it but the contactors have been...

I am looking for a good oil lab. I do not want to use Trane. Please let me know where you guys are going.

Dewey Elsik

I know that! I just asked for the part number!

Can someone please give me the part number for the UCP2 Comm 4 module for a CTV? You would think that after working on them for 15 years at Trane, I would remember which module it was. I need to try...

I am having a very hard time finding the BCI-R (Red Board) part number. I dont need the kit, just the board. Please let me know if you have the part number.

Dewey

No, it's not. We never setup the equipment. It's the installing contractors responsibility to prove that. I just did it because I knew how and had the software. Per our contract!

Well, its not in my scope to setup the Trane Unit. Problem is I was the go to guy at Trane. I am going to pass this on the them to figure out. Its not my problem. Thanks for the help.

Dewey

I have to wonder if I am Just thinking it is not controlling to setpoint because the compressor stages are not coming on. If I remember correctly, the 1st stage of cooling is economizer. I don't...

I am, it has a 69 deg zone temp and active zone temp setpoint of 65 (64 plus 1 deg offset) it's controlling to Dat setpoint which is out of service.

Next issue. This is a,single zone VAV profile. I can't seem to control it to zone temp.

BO-1 is enabled. I had to write a program to send a value to the BCI-R every 3 minutes. Works like a charm.

Thanks All!

If I can help anyome, please ask.

Dewey

I am not writing to the point continuously. I assume that is why I see a value and it shows failed. I know it reverts to the hard wired value after 900 seconds. But I would expect it to at least...

But it is, I have it scanned into and I can read all the values. It even controls to my setpoint. I have never seen this before. I have setup a lot of these of BCI's in the past at Trane.

Dewey

Guys, I am about to pull my hair out. I am a former Trane Controls Service tech (15 years). I have TU and know how to use it. I am trying to integrate to a BCI-R in a voyager. Its a not DAC. I have...

Come on guys, that is at least a 150 pound water box! That tube will take "MUCH" more. I have always just pulled the corks out when I was finished though!

You "MUST" enable the points with Tracer TU with the BCI-I it is "NOT" like a BCI-C! Make Trane Come back and do it right!

It is not legal to do without shutting it down and pulling the fuses. I agree, I would unplug the wires at the motors and megg the wires. We (Trane) had a bad problem with wires rubbing and chaffing...

Not all (actually most in my area) BMTS's have the rev 4 chip on them. You can get a device that will let you mix ARCNET and Ethernet. I have used them several times but the name escapes me right...

Morganizer does this too with an MP581 and the CTI on the reliatel controls. The only way to tell what profile you have is to look at it with Rover or NL Util and get the prog ID! You are going down...

Guys I have a lot of experience with this. I have even had to run special somtware in the drive to resolve one issue. Question #1 What frame drive? (how many doors are there on the drive). I will bet...

Guys I have a lot of experience with this. I have even had to run special somtware in the drive to resolve one issue. Question #1 What frame drive? (how many doors are there on the drive). I will bet...

Guys, a bit if advice. The new heater has 3 elements in parallel. You now need to check the current on that 750 watt heater. I have had a real big run on heaters lately. They would all heat but would...

Lots of copper in that there chiller. Don't give it away!

Not available with Hot gas bypass! Sorry!

I have replace "many" butterfly valves!

What he said: "This chiller would be a UCP1, there's no BACnet interface available for this chiller, neither is LON for that matter. You'll need a BMTW BCU to serve you info.


mallron
View...

We are Native Bacnet now with a BCI-(I,C,R)

You are refering to the Trane JCI 25 point Bacnet Template.

1

We only rent tanks to return refrigerant in. We have tanks for every type and oil! If the oil or refrigerant are bad, we rent a tank and pull the charge and then return it all. We (I) only use our...

It was not us, it was our supplier! I will only use a Filter 1592 by the way!

Deadhead a Pump? Oh my god you will ruin it! I actually had an engineer tell me that not too long ago! I told him to step aside while I do my job!

At $1500 for a condensate float ball for an ABTF, I am not surprised! We no longer make them!

Try sending it to me, if not try dewey.elsik@verizon.net. I have much more room there.

Thanks!

Dewey

say it again in English!

I have a YK with drive that has a very strange problem. I have been chasing this for months. The display will just go blank and go through the complete reboot process. I have checked all the...

We used that ZEP stuff on all the open drives when I was at Carrier. It works pretty good.

Dewey

Can you even buy Varsol anymore?

The IPAK BCI us setup for "custom" units. The BCI-C and UC800 can be changed with Tracer TU!

Everything you guys are asking for is available at Comfortsite. All you need to do is have either somenone at Trane or the Trane parts center set you up!

Hold it cowboys! The BCI needs Tracer TU to properly setup. On an IPAK it is prett easy. On a CH-530 chiller, you will need the appropriate version of firmware in your device. You cannot just add a...

Are they Trane RTU's? If so, what are you doing writing CPL? You need to set each RTU's configuration to reference the appropriate setpoint you want to use. Never fear, BCI-R is on its way for...