Search:

Wire strippers, mini split adapter for gauges, utility knife lost dozens of each lol

Go to my link drive.com helpful stuff from Mitsubishi

Is infinity touch the same as Bryant evolution connex

I carry an older ui (t-stat) with a short 4 wire whip abcd plug and you can hook up to evolution (Bryant) or infinity (carrier) furnaces or condensers

Honestly I like old school analog gauges better

Ak900 best bang for buck have had sman 3 loved them as well but don't take water very well

Awesome download thanks

Good read!

Their over complicated for sure, replaced an inverter board on one very pricey board if not warranty

No I didn't, don't know why I didn't think of that, my mind was flustered lol

Thanks rundawg very helpful, got a bad compressor then according to windings, as to the service bulletin unit is a 2014 with 3 other ev.extremes on same building w no problem

. .? For Bryant experts.... got a evolution extreme 280ana 36 might be missing a # Or two on model, ui is saying 77 inverter over current three times then going into 95 lockout, trouble shooting...

Thanks

Just for residential small water source hp, most of which I work on are open loop

Yes just reading press drop on water coax I think that setup would work

Sounds interesting lol

Do you just put standard pressure gauge on it?

What formula do you use? Is delta t of water x gpm x 500 for water (pump and dump) aka open loop correct ? If so how do you get your gpm? Is the flow restrictor size good enough or ?.

Looking to make or buy a tool to measure water pressure drop across a coax on wshp what do you use, something you can put into pt port

Zebra gator clips work good for me

Ditto on arrowhead hunting love it

Some of these had 20 yr warranties on heat exchanger if I'm not mistaken

Model # 58 something?

Koi pond?

Pro one t701, t721, t855, and Honeywell vpro8000 wifi

Negligence and lack of maintenance

:beat::beat: ever have four ppl watch you work for 3 hours then boss pulls on site and suddenly everyone gets real busy real fast, I'm a service tech and usually work by my self, work on a little...

Welfare bear ha lol that little green bear haunts me didn't realize there were empty tins all over my service van

Day 4 no nicotine cravings not so bad today, chewed sunflower seeds helped a lot not as irritable,

Ha lol I work with people who vape lol looks like some kinda drug pipe lol

Don't get addicted to dip way more nicotine released, just as bad for you

Good luck I'm on day three w/o nicotine today was hardest especially in between service calls

It's rough it's kinda kicking my butt, Ancy feeling all the time irritability

:Faint::Faint:long time dipper here at least can a day grizzly long cut wintergreen last 15 years, it's easier for me at home when I get in my service truck the cravings hit anyone else goin through...

Check dc micro amp of flame sense needs .5 or greater on most for board to sense flame

This was first time I've opened panels on one new experience for me

Thanks for help, found problem igniter electrode loose in ceramic housing, causing intermittent ignition failure

Yes am tech, not familiar nor comfortable with this equipment though that's why I'm asking, today was 1st time I've took panels off a tankless water heater,

I see gasket Must be replaced. I wonder if I can temp it in with high temp caulk until I can get replacement gasket?

Also first dipswitch was on on, anyone know what 1st is?

Said unit ran fine on l.p so I'm sure I've done something will be there bright and early to find out

Switch number 2 on for natural, .67 wc low fire 3.6 w.c highflier . gasket where igniter and flame sense crumbled to pieces could this cause? can I repair with high temp caulk?

Converted a residence from l.p. To nat g today they had a rinnia r53 tankless, I have no exp with tankless w.heaters, had a conversion kit that I followed worked till I left, lol customer just called...

Went to m&p class in Cincinnati(Hebron) was very informative highly recommend it, but 1st day was all there sales pitch, but class did count for all 16 of my nate hours!

Neat job! Nothing wrong with goodman/ amana in my eyes and were a bryant dealer lol.

Have seen this once on Rheem package heatpump, compressor was shot fan span at half speed with contacter not pulled in single pole as well

R.j Schuster author,

Has anyone read (101 ways to suck as an hvac tech)? Just finished it some real good reading I got a kick out of it, thinking of buying ( no ducks in the attic) anyone recommend it?

Done some work with them was on hold so long I had to charge labour that they wouldn't cover!

Just sent my uei dl379 in for warranty repair/replacement with similar issues, I couldn't get meter to read same mfd twice on same capacitor. And it took extremely long to read capacitance, also...