Search:

Type: Posts; User: perfectionist

Page 1 of 15 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    41
    Views
    1,620

    Couldnít you just turn the breaker off at the...

    Couldnít you just turn the breaker off at the panel and check the disconnect? Seems like the fastest way and a positive ID.
  2. Replies
    11
    Views
    656

    Have you done any work to it lately? I had that...

    Have you done any work to it lately?
    I had that happen after changing a flow sensor because a clip didnít seat right.
  3. Replies
    38
    Views
    3,919

    In the past I have either used the carrier zone...

    In the past I have either used the carrier zone system with UI that works very well or I use a static press transducer with a external variable speed drive which also works well. Just an FYI I see...
  4. Replies
    38
    Views
    3,919

    Nice looking job... is the furnace staged? How...

    Nice looking job... is the furnace staged? How are you managing the airflow when your smallest zone is on? Your sheet metal work looks great!
  5. Replies
    37
    Views
    1,116

    Did you try magic eraser? Not flammable and takes...

    Did you try magic eraser? Not flammable and takes just about anything off.
  6. Replies
    4
    Views
    2,634

    My YJ pump is 6 mo. Old and doing the same thing....

    My YJ pump is 6 mo. Old and doing the same thing. Keep us post if you find a solution
  7. Replies
    19
    Views
    2,557

    Beautiful job, I like the spacer between the...

    Beautiful job, I like the spacer between the furnace and A/C coil. Also like the return box on the bottom and the radius throat elbow is over the top! Nice work
  8. Iím interested.... can you email me some pics? Is...

    Iím interested.... can you email me some pics? Is this the original Ak9000 or is it a UEI ak9000?
  9. Do you have a thermal camera or know someone that...

    Do you have a thermal camera or know someone that does? There is a good chance that you may be able to find a slow leak that way, the water will be colder because of evaporation.
  10. I thought they banned thekux

    I thought they banned thekux
  11. Replies
    23
    Views
    2,031

    Nice job! 👍. Your metal work is over the top,...

    Nice job! 👍. Your metal work is over the top, looks great I like your return spacer/ base in the last pic... have you ever measured static on that or know what kind of equivalent length it works out...
  12. Replies
    12
    Views
    1,100

    Yes, 1 man company.

    Yes, 1 man company.
  13. Replies
    12
    Views
    1,100

    I agree that visually it is not as nice but I did...

    I agree that visually it is not as nice but I did that to keep the water away from the foundation, as it is the grade pitches toward the house. I piped the drain out to where I feel it will continue...
  14. Replies
    12
    Views
    1,100

    Thank you Ken

    Thank you Ken
  15. Replies
    12
    Views
    1,100

    It is restricted quite a bit and I had to have...

    It is restricted quite a bit and I had to have the propane co. come back to elevate the press. To 13Ē before I could get it to burn below 9%. Thatís my new Testo in the picture.
  16. Replies
    12
    Views
    1,100

    Recent installs

    It's been a while since I've posted .....been busy. Here is a Mitsubishi hyper heat and a new construction job that I just finished. The new construction job is almost 3000 square ft with a 26 '...
  17. Check out Fan Handler- LA240. Itís basically a...

    Check out Fan Handler- LA240.
    Itís basically a head press. control and it has worked great for me.
  18. Definitely missed it... been checking multiple...

    Definitely missed it... been checking multiple times a day!
  19. Replies
    14
    Views
    2,500

    Looks great!

    Looks great!
  20. I was at a new modular house to put in the HVAC...

    I was at a new modular house to put in the HVAC and I was drilling a hole in the shaft provided to get the line set to the second floor/ attic. I measured it out and took out my 3" hole saw and made...
  21. Replies
    29
    Views
    4,772

    The sheet metal work looks good. We are not...

    The sheet metal work looks good. We are not allowed to pan the joists and use the wall cavity as return anymore, it all has to be hard piped to the return. I thought that new code was for all of the...
  22. Replies
    18
    Views
    3,021

    Around here it RG&E for the gas and they have...

    Around here it RG&E for the gas and they have never made me change an existing valve of this style, if I were installing new gas line it would be the kind that does not require a tool to shut off. I...
  23. Replies
    18
    Views
    3,021

    Actually I don't own a break... I bend everything...

    Actually I don't own a break... I bend everything by hand and the metal is 24 Gauge so I'm not worried about it making noise or popping.
  24. Replies
    18
    Views
    3,021

    T&P drain line is code? Yes. If it blows on yours...

    T&P drain line is code? Yes. If it blows on yours it would enter the pan and the condensate pump would pump it out so maybe they let that go. If you didn't have the safety pan and pump would they let...
  25. Replies
    18
    Views
    3,021

    The expansion tank goes on every install now...

    The expansion tank goes on every install now because as the PRV's and water meters get changed out all of the new ones have check valves. Also it is in the WH manual to install it.
  26. Replies
    18
    Views
    3,021

    Recent installs

    I always forget to take the before pics, guess I am too focused on getting the new one in. I took out a vintage 1985 Trane 135k/BTU and put in this 2 stg. 60K/BTU. Then a couple of weeks later I...
  27. Replies
    23
    Views
    3,021

    I bought the 2" ratchet pvc cutter and it cuts...

    I bought the 2" ratchet pvc cutter and it cuts nice. No mess either, the only down side is if the pipe is cold or too close to the end it will break the pipe.
  28. Thread: Airflow

    by perfectionist
    Replies
    11
    Views
    1,296

    I would say the drawing on the left would be the...

    I would say the drawing on the left would be the most successful as long as you size it correctly. Also take a look at the # and size of the return registers.
  29. Replies
    37
    Views
    9,108

    No but the house next door did.... same size...

    No but the house next door did.... same size house and it has double the size equipment. 100k furnace and 3.5 A/C with under sized duct. Guess they wanted to showcase how the F it up all the time....
  30. Replies
    37
    Views
    9,108

    Homearama was is July.... it was on Mendon center...

    Homearama was is July.... it was on Mendon center rd in Pittsford. This house won all of the awards although when the show was happening the house got over temp because their was 80-100 people in...
  31. Replies
    37
    Views
    9,108

    I didn't catch this post when you made it.... I...

    I didn't catch this post when you made it.... I would be happy to look at your project. My email is in my profile.
  32. Replies
    37
    Views
    9,108

    Thank you Ken

    Thank you Ken
  33. Replies
    66
    Views
    7,356

    Miss Kate.... positive thoughts are coming your...

    Miss Kate.... positive thoughts are coming your way. Hope you are well and know that there a lot of people wishing the best for you.
  34. Replies
    47
    Views
    8,562

    Your looking at the first generation turbo...

    Your looking at the first generation turbo capacitor
  35. 1/2" cpvc is what I use then convert to vinyl at...

    1/2" cpvc is what I use then convert to vinyl at the last 6" before the pump
  36. Replies
    56
    Views
    2,619

    Another 10 year war would also help copper and...

    Another 10 year war would also help copper and brass rebound....need lots of Bullets
  37. Replies
    37
    Views
    9,108

    It's the kitchen hood exh., if you look closely...

    It's the kitchen hood exh., if you look closely to the sideways pic I labeled it kitchen exhaust and thank you.
  38. Replies
    37
    Views
    9,108

    That's what the load calc came out to. 700 sq ft...

    That's what the load calc came out to. 700 sq ft is in the basement so doesn't need much of either. I have been putting 40k furnaces I 2000sq ft houses since I started using manual j . It works or I...
  39. Replies
    37
    Views
    9,108

    Only 7"WC around here, other than the large...

    Only 7"WC around here, other than the large piping is not so ad because we don't have to have step down regulators.
  40. Replies
    37
    Views
    9,108

    Any reason why? It's the first Lennox furnace I...

    Any reason why? It's the first Lennox furnace I have installed.
  41. Replies
    37
    Views
    9,108

    A new construction job

    This is a new builder that I am doing work for, this job is actually part of a home show in this area (homearma). I have some pics of the ruff where I insulated the metal bath exhaust and the metal...
  42. Replies
    39
    Views
    3,176

    Ha it's not the first time I've been banned for...

    Ha it's not the first time I've been banned for that
  43. Replies
    39
    Views
    3,176

    I ban you for posting after being banned

    I ban you for posting after being banned
  44. Maybe he bought the propress because his solder...

    Maybe he bought the propress because his solder joints looked like the rest of the install.
  45. Thread: ummm

    by perfectionist
    Replies
    34
    Views
    9,085

    Close enough? I don't think so.

    Close enough? I don't think so.
  46. Replies
    15
    Views
    5,628

    That's the biggest drain pan I've ever seen!

    That's the biggest drain pan I've ever seen!
  47. Replies
    11
    Views
    3,169

    Speaking of satellite guys I was at a house where...

    Speaking of satellite guys I was at a house where they tied the dish ground to the lighting rod ground :eek2:
  48. Replies
    19
    Views
    6,851

    I showed my dog this video and he was pissed!

    I showed my dog this video and he was pissed!
  49. Replies
    64
    Views
    6,668

    .And Never Ever use the BTU gain from Manual J...

    .And Never Ever use the BTU gain from Manual J to size equipment[/QUOTE]

    I thought that was the whole point of doing the load calc. Now you've got me confused..... I have been using Wrightsoft...
  50. I wonder if a thermal camera would show the...

    I wonder if a thermal camera would show the difference.
Results 1 to 50 of 742
Page 1 of 15 1 2 3 4