measure the cabinet from the air cleaner and see if you can get a 4" or 5" pleated filter to fit it.
if you can put one there then remove the one from the filter grill.
Just purchased a 10 year old home and discovered during the inspection that the air handler is new, but that there is a slot for an electronic air cleaner, but the slot is empty...meaning there is no electronic air cleaner/filter. There is a pleated filter in the ceiling leading to the air handler. Also the HVAC unit is a heat pump, if that matters. My question is whether I need to purchase an electronic filter, or is it okay to leave the space open and just use the pleated filter with a high MERV rating?
measure the cabinet from the air cleaner and see if you can get a 4" or 5" pleated filter to fit it.
if you can put one there then remove the one from the filter grill.
Not quite sure what you mean...the Filtrete filter I am currently using is a 20x30x1 MERV 12 in a drop down grate from the ceiling. I presume the air handler is above that with the open hole where there used to be an electronic filter. Are you suggesting removal of the filter I am using and just put a smaller one in the air handler?
the frame size may be smaller, probably 16 x 25 or 20 x 25 but at 4-5" thick it will give you more filter surface area and less resistance. also having the filter right at the unit will trap any dirt that gets into leaks in the return duct after the return grill.
Thanks...are filters of that thickness readily available at a Home Depot or Lowe's?
Why will I be calling a contractor?
I just checked the unit and it is a 4 ton unit....so does that make a difference with the 20x30x1 filter?
Although I appreciate your reply, it does no one any good to say something is a BIG PROBLEM unless you have the expertise to explain WHY....
4 ton requires 800 sq inches of non pleated filter area. (If filter is 1" thick). You have 600. Not enough for 4 tons. Causes air flow restrictions which in turn causes premature wear and tear on all parts - electrical and mechanical. Causes abnormally high head pressure in heat and low suction pressure in cool. Also increases power usage.
Great info....so the obvious question is....what is the recommendation?
The air handler has a Honeywell electronic air cleaner...would a pleated filter (20x25x4 1/2 MERV 12) in this unit be acceptable and does it relate to the issue of the 1" filter in the return air grate in the ceiling leading to the air handler?
I'll leave your question to be answered by bamacool.
just wanted to tell you that media filters can be used in the
return air filter grill you have. without having to change the
r/a filter grill to accomidate media filter.
check with hvac supply house, or with your hvac company
for filters like the one in the pic attached.
if you to upsize the return duct & r/a filter grill..
use the filter grill that is made for media filters.
I use 20x25x4 for my 2 ton system.
best of luck
The cure of the part should not be attempted without the cure of the whole. ~Plato
This is the Ask Our Pro's forum. In order to post a response here, you must have verified qualifications and have been approved by the AOP Committee. You may ask a question by starting a new thread.
You can find the rules for posting and qualifications here.
Additional infractions may result in loss of posting privileges.
Last edited by jpsmith1cm; 01-31-2013 at 05:27 AM. Reason: non AOP member
Calgary_hvac
This is the Ask Our Pro's forum. In order to post a response here, you must have verified qualifications and have been approved by the AOP Committee. You may ask a question by starting a new thread.
You can find the rules for posting and qualifications here.
Additional infractions may result in loss of posting privileges.
Thanks...I inserted a 20x25x4 pleated filter into the slot where the electronic filter components reside at the air handler...it is a MERV 12 rated filter. I also have a 20x30x1 in the return air grate in the hallway ceiling which leads up to the air handler. I was told that the Honeywell electronic air filter components can be replaced by the pleated filter. I hope that is correct information.
Thanks...I inserted a 20x25x4 pleated filter into the slot where the electronic components reside in the Honeywell electronic air filter located inline at the air handler. I was told that was acceptable...I hope that is correct information. I also have a 20x30x1 pleated filter in the return air grate located in the ceiling leading to the air handler...
i would remove the filter at the grill if you're still using a merv12 filter there, too much restriction to airflow with 2 filters.
if you want a filter at the grill just use the fiberglass filters, no pleated filter.