Results 1 to 13 of 14
Thread: hvac
-
01-19-2010, 08:39 PM #1
New Guest
- Join Date
- Jan 2010
- Posts
- 1
hvac
I recently ran into this problem, was no flame to start with I 've changed the limit switch,ignition module, flame burner with sparking wire, i got the flame but won't stay on more than 5 minutes what it could be the problem? coil is clean i did not see any kinked duct, blower motor on low speed.
so any ideas? thanks.
-
01-19-2010, 08:50 PM #2
Professional Member
- Join Date
- Jun 2009
- Location
- Bakersfield, Ca
- Posts
- 1,716
What parts haven't you changed? You probably only have a few left! You'll get it, I'm counting on you.
-
01-19-2010, 08:52 PM #3
Global Moderator/AOP Committee
- Join Date
- Sep 2008
- Location
- Western PA
- Posts
- 21,332
It's broken.
Clearly you need a new furnace.
-
01-19-2010, 08:56 PM #4
Professional Member*
- Join Date
- Jan 2008
- Posts
- 1,598
DavyB said it all. Change a few more and you've got it!!
"Hey Lama, hey, how about a little something, you know, for the effort." And he says, "there won't be any money, but when you die, on your deathbed, you will receive total consciousness." So I got that goin' for me, which is nice. - Carl Spackler
-
01-19-2010, 09:02 PM #5
Regular Guest
- Join Date
- Mar 2008
- Location
- Over the river and through the woods
- Posts
- 116
Place a service call to a qualified HVAC company...Its gotta be cheaper then putting your parts supplier's kid thru collage.....
-
01-20-2010, 07:01 AM #6
Professional Member
- Join Date
- Jun 2006
- Location
- Omaha, Nebraska
- Posts
- 766
You replaced the limit switch. Is it the adjustable type, and did you set it correctly?
-
01-20-2010, 09:49 PM #7
Professional Member
- Join Date
- Jan 2007
- Posts
- 31
DIY?????
-
01-21-2010, 12:31 PM #8
Professional Member*
- Join Date
- Jul 2009
- Posts
- 56
do you think diy ?????? lmao.....
-
01-21-2010, 01:51 PM #9
Professional Member
- Join Date
- Feb 2009
- Location
- God's country
- Posts
- 36
Check temp rise and clock the gas meter....
-
01-21-2010, 02:09 PM #10
New Guest
- Join Date
- Jan 2010
- Posts
- 1
New to site want to say hello to all members. Need any advice iI can get, need any info on websites for transitions on rigid ductboard. Haven't had to cut in forever and had to go back to installing recently. Don't want to spend all the money on books and dont want to waste ductboard and look like idiot!! Thanks
-
01-21-2010, 02:25 PM #11
Professional Member
- Join Date
- Feb 2009
- Location
- God's country
- Posts
- 36
a geometry book will help...... and lots of tape....
-
01-21-2010, 03:58 PM #12
Banned
- Join Date
- Oct 2003
- Location
- Washington
- Posts
- 7,405
Need to open up your own thread. You will receive valuable knowledge here but you should still buy some books.
Originally Posted by joe trafford
Why the hell you want to use ductboard anyway....
-
01-21-2010, 07:47 PM #13
Professional Member
- Join Date
- Jun 2006
- Location
- Omaha, Nebraska
- Posts
- 766
I don't know why, but the whole island here is full of it. Hardly any sheet metal at all. I figure maybe no one knows how to use a brake... Originally Posted by seatonheating
Why the hell you want to use ductboard anyway....
Reply With Quote
