Results 1 to 9 of 9

Thread: York Talk help

Hybrid View

  1. #1
    Join Date
    Dec 2008
    Posts
    9
    Post Likes

    York Talk help

    Hi,
    I am trying to get to Know The York talk interface on the York chillers at the site where I work, I am connecting Via an ISN, and can log in ect,

    Has anyone got a simple user manual, key commands ect to speed up my progress

    Many Thanks

    Shovell


  2. #2
    Join Date
    Sep 2007
    Location
    Somewhere in the world.
    Posts
    1,660
    Post Likes

    Wink

    This may seem like a stupid question but there are 4 generations out there first there is a Chiller link which is a APC modified card York Talk 1 , second there is XL-Translator APC interface to microgateways which would be third party selection Lon , Bacnet , ASCII , N2 , DataBridge York Talk 2. , third there is just the microgategay to microgateway configuration York Talk 3. Here is the kicker York talk 1 can pretty must talk to any older Chillers slower baud rates due to microboards , York Talk 2 can talk to air side or water side Chillers next level baud rates due to microboards , York Talk 3 is strictly optiview panels only most current baud rates or higher due to microboards , unless your very comfortable with this I would not recommend it , and then there is the E-Link which is a whole nother animal I don't even want to get into that one. So what are you talkin to style Chiller , microboard # , etc.
    A mind is like a parachute. It doesn't work if it is not open.

    The best part of going to work is coming back home at the end of the day.

    Hard work spotlights the character of people: some turn up their sleeves, some turn up their noses, and some don't turn up at all.

  3. #3
    Join Date
    Dec 2008
    Posts
    9
    Post Likes
    We are running two 3 system chillers (YCAS) on 1095 Micro Board, and One (YCIV) 2 system Chiller on E-Link, the latter not on the ISN (EDC 36)

    I am trying to pull data and configure the ISN via, Putty, and have been relatively successful, but need some pointers in short cuts / key strokes to edit the ISN data. The chillers are not currently under control of the ISN, we are controlling with Local water temp. set point.

    we are looking to move to a central all inclusive control system, so we are trying to "Revive" the ISN, possible put the YCIV through it as well, then look our control logic to improve efficiency.

    Any pointer would be greatly appreciated

    Shovell

  4. #4
    Join Date
    Sep 2007
    Location
    Somewhere in the world.
    Posts
    1,660
    Post Likes
    What protcol are you using to talk to those Chillers , both of those Chillers would be talkin in York talk 2 that is the YCAS & YCIV.
    A mind is like a parachute. It doesn't work if it is not open.

    The best part of going to work is coming back home at the end of the day.

    Hard work spotlights the character of people: some turn up their sleeves, some turn up their noses, and some don't turn up at all.

  5. #5
    Join Date
    Sep 2007
    Location
    Somewhere in the world.
    Posts
    1,660
    Post Likes
    So if your running in local then must be just pulling data from the Chillers only ?
    A mind is like a parachute. It doesn't work if it is not open.

    The best part of going to work is coming back home at the end of the day.

    Hard work spotlights the character of people: some turn up their sleeves, some turn up their noses, and some don't turn up at all.

  6. #6
    Join Date
    Dec 2008
    Posts
    9
    Post Likes
    That's right, were not using the ISN to perform control of the Chillers, we are running in local.

    But we need to move to a better, more efficient control scheme, That why we are trying to revive the ISN, and York talk. We have not used the ISN to control the chillers for quite some time and it has lost some set up parameters and set points, that were we need help in setting up , editing changing set points to revive the ISN.

    It's seems we do not have a simple instruction book, I need to understand the editing, saving functions

    Do you have access to a user manual.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Quality Home Comfort Awards