Results 1 to 13 of 23
Thread: York YTK Manual
-
12-09-2009, 08:47 AM #1
Regular Guest
- Join Date
- Dec 2009
- Location
- Texas
- Posts
- 4
York YTK Manual
Does anyone know where I can get a manual for a York YTK?
-
12-09-2009, 01:27 PM #2
Regular Guest
- Join Date
- Dec 2006
- Posts
- 39
More info is needed, full model and serial number would help. There is many manuals for many Yt's.
-
12-10-2009, 10:16 PM #3
Professional Member*
- Join Date
- Dec 2008
- Location
- Dixiana, AL
- Posts
- 2,487
As Buck said, a YTK what? If you want service lit on centrifugal chillers, you also need to put something in your profile about who you are and what you do. Gives the rest of us a warm fuzzy feelin'..............
-
12-11-2009, 05:35 AM #4
Professional Member*
- Join Date
- Sep 2007
- Location
- Somewhere in the world.
- Posts
- 1,437
As someone once told me help me help you.
Arguing with your Boss is like wrestling with a pig in
mud.
After a while you realize that while you are getting
dirty, the pig is actually enjoying it.
It is not exactly cheating, I prefer to consider it
creative problem solving.
-
12-11-2009, 07:17 PM #5
Regular Guest
- Join Date
- Dec 2009
- Location
- Homestead,FLA
- Posts
- 5
Do you know the axial thrust on the low speed for a YDTL 108?
-
12-11-2009, 09:26 PM #6
Professional Member*
- Join Date
- Dec 2008
- Location
- Dixiana, AL
- Posts
- 2,487
Yes.
Originally Posted by MQ03122
-
12-11-2009, 10:17 PM #7
Regular Guest
- Join Date
- Dec 2009
- Location
- Homestead,FLA
- Posts
- 5
What's the answer?
-
12-11-2009, 10:39 PM #8
Professional Member*
- Join Date
- Dec 2008
- Location
- Dixiana, AL
- Posts
- 2,487
Look at post #3 in this thread. Then go and pick out a few personal profiles of members, myself included if you'd like, see what's in them, and then tell all of us about you. I doubt seriously that you are a beginner or handyman if you know what axial thrust is, but if you're new here, be kind enough to indulge the rest of us with some of your history if you want answers to questions about large-tonnage equipment. It's only fair. Originally Posted by MQ03122
A question to the keepers of the forum: When is the "Chiller" section going to be put under the pro heading???
-
12-12-2009, 12:43 PM #9
Professional Member
- Join Date
- Oct 2006
- Location
- Central Texas
- Posts
- 556
I don't know.... strikes me as a little weird you only want that measurement. Get a teardown manual, that'll tell you ALL the proper mic readings. Originally Posted by MQ03122
Sic Semper Tyrannis.
-
12-15-2009, 09:16 PM #10
Regular Guest
- Join Date
- Dec 2009
- Location
- Homestead,FLA
- Posts
- 5
The reason I only needed that answer was because its not in the manual.I was able to figure it out.By the way gentleman I updated my profile.Sorry I skipped it earlier,it was not my intentions. Originally Posted by txhvac
-
12-15-2009, 09:35 PM #11
Professional Member
- Join Date
- Nov 2008
- Posts
- 308
Now you have me interested. Originally Posted by MQ03122
So what is the specs. on the thrust?
-
12-15-2009, 10:12 PM #12
Professional Member*
- Join Date
- Dec 2008
- Location
- Dixiana, AL
- Posts
- 2,487
Interests me, too. This isn't an equation, it's a factory construction tolerance. How did you figure it out?
-
12-16-2009, 07:54 AM #13
Regular Guest
- Join Date
- Dec 2009
- Location
- Homestead,FLA
- Posts
- 5
You're right.I just happen to find other teardown manuals on the previous compressor model and matched it against the compressor I just overhauled.Had to match all parts and so on.But thanks anyways.I'm here to help anyone.I'm willing to share my brains."Sharing is Caring"
Reply With Quote
