New Micron Guage - Page 5
Page 5 of 5 FirstFirst 12345
Results 53 to 58 of 58
  1. #53
    Join Date
    Jun 2008
    Location
    Rochester, NY
    Posts
    334
    This is pretty much the setup I use.
    http://www.yellowjacket.com/HVACRPro...&l=2&c=17&p=58

    Has anyone had their YJ core removal tool leak yet? Mine actually just broke too. The female part that screws on the port popped off

    -Mark

  2. #54
    Join Date
    Jun 2004
    Location
    Location:Raleigh NC
    Posts
    9,587
    I ve the YJ (x2) and the C&D (x2) the C&D are better then the YJ I, have to rebuild the YJ more often.
    If you help others then you are a Success

  3. #55
    Join Date
    Jan 2008
    Location
    In the work truck
    Posts
    2,990
    looking at the specs what makes this gauge so much better then the other??

    I have a CPS nothing special i think its a vg2000 or something. anyway its accuracy is +/- 10%. (as is the supco)

    this thread could have come at a better time. my buddy and me put his new supco and my guage on just the vacuum pump and other times on the gauges.

    they were consistently about 30-100 microns off when still pulling a vacuum but when allowed to stand it was a couple hundred off. his was always higher!

    mine would hold around 300-500 standing and his would be 750 to 1100.

    so even if i assumed his was off 10% to the low side and mine was off 10% to the high side they still were 100 microns or so off from each other when i think they sould be closer to a middle figure..

    anyway this looks to be the same accuracy just looking to see why this is better?
    Gotta have the right tool for the job!

    Where is all the stuff MADE IN THE USA?

    "Thats what we do Troy. Incredible, Invisible, Imbelivable things. We are an Unseen, Unknown, Unvincible fraternity of craftsman.."

  4. #56
    Join Date
    Oct 2008
    Location
    New Jersey
    Posts
    1,015
    It seems like my supco vg64 is not very consistant, i can put it on the same set of gauges, pull a vacum twice for the same amount of time and i will get two totally diff readings, i mean its supposed to be consistant right? Its really got me thinkin of buyin another one, something that is a little better.
    I dont install leaks, i just fix em

    Sig line removed by Admin*

    Lets see if this gets removed..............

  5. #57
    Join Date
    Jan 2008
    Location
    In the work truck
    Posts
    2,990
    klienman was the buddy i was talking about....

    hes more paranoid about these things then i am lol haha
    Gotta have the right tool for the job!

    Where is all the stuff MADE IN THE USA?

    "Thats what we do Troy. Incredible, Invisible, Imbelivable things. We are an Unseen, Unknown, Unvincible fraternity of craftsman.."

  6. #58
    Join Date
    Oct 2008
    Location
    New Jersey
    Posts
    1,015
    Well after a little research i found one from inficon that doesnt look too shabby.......

    http://www.hvacr-tools.com/mm5/merch...e=VACUUMGAUGES
    I dont install leaks, i just fix em

    Sig line removed by Admin*

    Lets see if this gets removed..............

Page 5 of 5 FirstFirst 12345

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event