-
Did someone say something about naked cheerleaders?
-
 Originally Posted by Freezeking2000
Zip ties do not last nearly as long as good electrical tape.
Didn't know that. Thanks... Even good black zip ties? I guess I could see good electrical tape holding up well.
-
 Originally Posted by acobra289
Assuming you don't want to keep your reasons secret, is there anything that can be brought to the attention of the company to have it corrected? Or are your reasons based on cosmetic issues?
As for the disconnect box, if it passes inspection, great, If not, it doesn't seem that big of a deal to move it to where it needs to be.
Concerning the condensate drain freezing during winter, what is the usual solution to this problem? My last furnace was an 80, so I have not dealt with this before.
Any other issues I need to bring to their attention?
Thanks.
1-Gas supported to appliance.....
2-condensate breather for proper pressure and flow..
3-is that armour flex joining the evap drain and furnace condensate?
4-I perfer to put in-take outside for better efficiency...
5-clean the electrical wires up...{from the old t-stat wires join the new}
6-the dryer vent is to close to the condenser for my liking....nothing like plugging the condenser up with lint....
thats just to name a few things......
-
 Originally Posted by wpg_hvac-r_redseal_
1-Gas supported to appliance.....
2-condensate breather for proper pressure and flow..
3-is that armour flex joining the evap drain and furnace condensate?
4-I perfer to put in-take outside for better efficiency...
5-clean the electrical wires up...{from the old t-stat wires join the new}
6-the dryer vent is to close to the condenser for my liking....nothing like plugging the condenser up with lint....
thats just to name a few things......
those IDIOTS used armour flex to keep the floor from getting wet when the drain sweats. furnaces have positive pressure drains, therefore p-traps are not needed. they do need to be capped.
the Dude stated in an earlier post that the furnace drain and the a/c drain need to be seperate, He's 100% right.
-
We don't do a lot of furnaces,the only thing I'd change is the way each return enters the furnace.May not be an issue ,but lower static would be gained,but may not be needed,can't tell from here.
Have the static checked,is the best advice .
-
 Originally Posted by superd77
the Dude stated in an earlier post that the furnace drain and the a/c drain need to be seperate, He's 100% right.
Or at least an air gap after the condensate trap. Surprised no one has focused on that as it's a safety hazard. It's a direct connection between the heat exchanger and the supply air.
"The American Republic will endure until the day Congress discovers it can bribe the public with the public's own money.
- Alexis de Toqueville, 1835
-
 Originally Posted by DeltaT
Or at least an air gap after the condensate trap. Surprised no one has focused on that as it's a safety hazard. It's a direct connection between the heat exchanger and the supply air.
If it wasn't on a positive pressure drain, and ran further then it does, it would be a concern.
-
 Originally Posted by beenthere
If it wasn't on a positive pressure drain, and ran further then it does, it would be a concern.
So it's not really a concern?
And what is this armour flex they speak of? Is that the black pipe insulation on the trap?
Thanks.
-
How much clearance is there between the wall and the unit? Looks too close from the pic..
-
 Originally Posted by acobra289
Is that the black pipe insulation on the trap?
Thanks.
Yep
-
Is that a garden hose next to the condenser? 
Is that writing on the insulation covering the return air? OMG!!
__________________________________________________ _______________________
“Experience is a hard teacher because she gives the test first, the lesson afterwards". -Vernon Law-
"Skilled Labor Isn't Cheap, Cheap Labor Isn't Skilled" - Unknown
-
 Originally Posted by Mr Bill
Is that a garden hose next to the condenser?
Is that writing on the insulation covering the return air? OMG!!
He's gonna need it with the drier exhaust and that spine fin.
-
 Originally Posted by RyanHughes
He's gonna need it with the drier exhaust and that spine fin. 
O so we can we chalk that up as a good thing about the install? 
I know I am terrible I try to find some of the good things in life.
__________________________________________________ _______________________
“Experience is a hard teacher because she gives the test first, the lesson afterwards". -Vernon Law-
"Skilled Labor Isn't Cheap, Cheap Labor Isn't Skilled" - Unknown
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Related Forums
The place where Electrical professionals meet.
|