View Poll Results: Do you use a micron guage when pulling a vacuum?
- Voters
- 128. You may not vote on this poll
-
Yes
-
Nope, we don't own one.
-
At least this pole shows a good thing, over 90% of pro's here are using micron gauges.
-
How many of you guys put on a filter drier when you seal up the system?
Seen a lot of guys pulldown to a good vacuum but no filter..
Attitude was if it needed one the factory would have provided one.
-
I never heard of a micron guage until 410a. use it every time because i no longer will install r-22.
-
 Originally Posted by hvaclover
How many of you guys put on a filter drier when you seal up the system?
Seen a lot of guys pulldown to a good vacuum but no filter..
Attitude was if it needed one the factory would have provided one.
Always, if not factory provided
-
 Originally Posted by refrtech
IMHO only a HACK would pull a vaccum on a system w/out checking the micron level . That is truely the only way to be 100% sure that you have zero leaks and that the system is contaminent free .
Again just my opinion
No offense, but contaminents are removed by a good flushing (acid, oil sludge, stuff like that) a vacuum pump will remove air along with moisture and non condensibles.
Last edited by hvaclover; 06-22-2008 at 11:36 AM.
-
we mandate that every time a system is open a new filter dryer is installed.
-
 Originally Posted by coolmen
I never heard of a micron guage until 410a. use it every time because i no longer will install r-22.
And that ok Buddy we all started somewhere unlike some here that will make you feel so bad and belittle folks because they were born with a micron gauge in there butt and a NATE certificate in there hand and a Sling Psychrometer in there teeth. Rather than putting folks down here that haven't used these few tools of the trade we "Pro's" should be encouraging old and new Pro's that haven't been using these tools how these tools can be beneficial to them in servicing a/c equipment. I guess instead of the sarcasm and put downs use our knowledge and experience and treat these folks as students and teach them as any good teacher should, remember none here knows it all anyway, but if we all work "together" we can all gain knowledge from one another, "maybe" even something we did not know, just my two cents.
__________________________________________________ _______________________
“Experience is a hard teacher because she gives the test first, the lesson afterwards". -Vernon Law-
"Skilled Labor Isn't Cheap, Cheap Labor Isn't Skilled" - Unknown
-
 Originally Posted by coolmen
I never heard of a micron guage until 410a. use it every time because i no longer will install r-22.
Whole new thread. But you're right, 410 will MANDATE micron guages usage.
And holding a neagative press for leak detection will become problamatic.
410A driers are so much more hygroscoic you stand to contaminate the drier if you have a leak with the systeem under vacuum.
I think that $400 Robinaire micron tester is for me.
-
 Originally Posted by Mr Bill
And that ok Buddy we all started somewhere unlike some here that will make you feel so bad and belittle folks because they were born with a micron gauge in there butt and a NATE certificate in there hand and a Sling Psychrometer in there teeth. Rather than putting folks down here that haven't used these few tools of the trade we "Pro's" should be encouraging old and new Pro's that haven't been using these tools how these tools can be beneficial to them in servicing a/c equipment. I guess instead of the sarcasm and put downs use our knowledge and experience and treat these folks as students and teach them as any good teacher should, remember none here knows it all anyway, but if we all work "together" we can all gain knowledge from one another, "maybe" even something we did not know, just my two cents.
That is why you are a gent Mr. Bill.
-
 Originally Posted by hvaclover
No offense, but contaminents are removed by a good flushing (acid, oil sludge, stuff like that) a vacuum pump will remove air along with moisture and non condensibles.
Sorry I was not more specific clover but IMO anything that may be in the system EXCEPT for refrigerant and oil is a contaminent .
-
 Originally Posted by hvaclover
That is why you are a gent Mr. Bill.
........ and I am not , but hey I never claimed to be !!
-
 Originally Posted by refrtech
Sorry I was not more specific clover but IMO anything that may be in the system EXCEPT for refrigerant and oil is a contaminent .
No use splitting hairs. We probably have some regional terminology here that would not agree with some of the every day procedures used in your neck of the woods.
-
 Originally Posted by refrtech
........ and I am not , but hey I never claimed to be !! 
You're one of the best. Don't be humble.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Related Forums
The place where Electrical professionals meet.
|