Network 8000 software

[scarletspider]

ok found some bulletin info , it was a cable from printer that was conflicting system, have it all up now. is there any "newer" software - front end- that would run this gcm 8000 system or is signal it for this older product?. also if the costumer wanted to replace this system with something newer, what are my options so that it stays open for us to work on and service, we not anybodys authorized dealer or factory trained representative...and also retain as much of the existing hardware/controllers as possible.

[berg2666]

I have them - do you need them?

You have XPSI, i am going to hit you up on email.

[berg2666]

i sent you the troubleshooting guide and the mz2 programming guide... hope that helps

i have xPSI... i don't know if i can distribute it though?

Me too me too for the manuals

[kevinbrock]

need your email to send the manual

[berg2666]

need your email to send the manual

I will email it to you ...... I thought it was in my profile after I send you the email from me i will go check my profile for accuracy.. Thanks

[Cuziwanano]

to a DOS based computer.
Have XPSI, MZ but no documentation. Any manuals for trouble shooting, programming BC would be awesome. Shows all site as "Empty" and "Disconnected".

Any help would be really appreciated.

[controltec]

Check your email I sent you some stuff.

[kelvin]

I have them - do you need them?

yeah. I'll send you an e-mail

[A.E]

hey guys i m new here n i really need literature on MZII n GCM
any pdf related to this will be appreciated
thanx
my email: Email Address Removed

[The_USC_2001]

I am in need of the Micronet software. I need to look into a Micronet program for integration reasons.

[A.E]

hello

i need manual for MZII, XPSI,MFII and others related documents.
If anyone hav these manuals kindly send me
my email is n my profile.

[Salmon]

hello

i need manual for MZII, XPSI,MFII and others related documents.
If anyone hav these manuals kindly send me
my email is n my profile.

[Salmon]

I have them - do you need them?

Could you please send me one ? I need them so much ! Many thanks !

[A.E]

Yes i do need those manuals. Can u plz send me at my email.
I will be very thankful to you.

[Twilson58]

Gentlemen,

I have a school system that has a Network 8000 that has lost all communication. Whatever the temperature setpoints were when the software crapped out has become the default.

What are their options other than replacement?

[The_USC_2001]

ALC has a great replacement for the Microzone II Modules. It is called a WebZONE. You take the internal board out of Microzone and replace it with the Automated Logic WebZONE board and just like that is is now a ALC Module.

[jim martin murphy]

hvac teacher,

I also need the software for the Barber Colman LAPT-80800-PSI and EPSI. I could use the connection to the laptop, please help me if you can.
Jim

[kelvin]

ALC has a great replacement for the Microzone II Modules. It is called a WebZONE. You take the internal board out of Microzone and replace it with the Automated Logic WebZONE board and just like that is is now a ALC Module.

Do you use the WebCtrl software?

[The_USC_2001]

Do you use the WebCtrl software?

Yes

[gbstech]

Hi everyone,
I too have inherited a Network 8000 system and need to make changes as some of the equipment is being changed. I have a GCM with 8 MZII controllers. I could really use the programmers manuals for both. The software is xpsi and nabworks. So i should have access to the controllers.

Many Thanks