Network 8000 software

[Carlos Rojas]

Hi,
I need a copy of XPSI.

[expertsrb]

thanks for any help you can give, and mabey a copy of xpsi, I have updated my profile and email address,

Thanks in advance for any help

scott

[Igotworms]

Controltec could you also send me those manuals? TIA

[controltec]

Igotworms

You've got mail. Feel free to call me if you need anything.

[berg2666]

WHat bare the hyperterminal settings???????????

[joey791]

OOOOOOOOHHHHHHHHHHHHHHHHH manuals hook a brother up please

[controltec]

hyperterminal settings will vary depending on what was setup in the GCM. Usually 8 none and 1 with a 9600 baud works just fine. You will need a 9 to 25 pin serial cable. Depending on the type of cable you have you will have to use the dte to dce switch inside the cabinet on the port you are connected to. I usually pick a baud rate and then try the switch in one direction, if it doesn't work flip it and try again. you will also have to hit the enter key to wake the GCM up and create a connection.

[tsmsp99]

Can someone please send me the manuals on Microzone II's?

[juliop360]

Hi can I also get link to the manuals please. I have the Barber-colmon network 8000 microzone 11 (GCM-84221-1 GLOBAL CONTROL MODULE found this in cover control#377y) <<this one has key pad. 2 Microzone wall mounts (#MZ2A-105-0-1-1 found in cover system manual F-25571). 2 barber-colman network 8000 LCM/Microzone 11 also found this in cover control#377y. Building I run has no manuals at all. Can someone send me the operators/programming manuals as pdf or a link would be great.

thank you

[controltec]

Julip360

I sent you a link for a download of all that I have.

Enjoy!

[juliop360]

Thank you this will help a lot

[jaceski]

Julip360

I sent you a link for a download of all that I have.

Enjoy!

Can you send me the link also?

[jaceski]

Whatever anyone has is appreciated...

[controltec]

Jaceski

I sent you an email with a download link.

[incontrol]

We also can integrate this old stuff into Niagara AX technology to get you into the 21st century.

You can bring microzones and pems into AX?

[controltec]

sure we use a ASD driver for this. Works really well. We have probably integrate over 50 sites like this. The driver will also allow you to still use the PSI software and tunnel down through the Jace for remote programming and diagnostics. If you would like to see some demos of the systems that we've done hit me up with my email that is in my profile.

[BC tech]

Heck I have sites with NET 8000 on WIN 3.1 and DOS , customer does even know the INTERNET exsists.

I relate to that. Been doing B-C service since `77. Have spare parts for Net2100, CPM, etc.
I always thought HVAC stuff was supposed to last 30years. WIN3.1 and DOS sounds like QNX Host8000 also.

[Control Man]

Yes the OLD QNX Host setup , been doing BC since 86 when they introduced the NETWORK 8000 to replace the NETWORK Supervisor system. Still quite a few standalone panels using QUME monitors.

A lot upgraded to SIGNAL and as long it still runs / repairable customers have no intention of replacing it

[CoolingTower]

Need to interface Microzones into AX. I have ASD driver updated in Jace. Looking for manuals and XPSI or PSI software.
Any help is appreciated. Thanks.

[controltec]

CoolingTower

You've got mail. I sent you a link to download all that I have. If you need any help let me know!