Results 1 to 7 of 7
  1. 01-05-2013, 11:50 AM #1
    tech-c2
    tech-c2 is offline Regular Guest
    Join Date
    Sep 2005
    Location
    Windsor Ontario
    Posts
    17

    Payne no blower during heat.

    I looked at a friends payne pg9mtav36075abss furnace the other night. The blower will not come during the heating cycle unless you turn the fan to on. I dont have much experience with the new furnaces with the ecm motors as I do primarily comercial and industrial work. I am suspecting the blower control board. Has anyone else had this issue with the new Payne furnaces?

    Thanks
    Reply With Quote Reply With Quote
  2. 01-05-2013, 12:04 PM #2
    Joehvac25's Avatar
    Joehvac25
    Joehvac25 is offline Professional Member*
    Join Date
    May 2012
    Location
    Upper Michigan
    Posts
    3,085
    I don't think that has a ECM blower. So the board won't turn the blower on in heat mode but when you turn stat to on it runs? We aren't supposed to give DIY advise here more so people can't google the answers. Can you go pro?

    Edit I see you have the 15 posts required, in the closed forums you will get better answers
    Reply With Quote Reply With Quote
  3. 01-05-2013, 12:48 PM #3
    pauls heating &'s Avatar
    pauls heating &
    pauls heating & is offline Professional Member*
    Join Date
    Feb 2010
    Location
    butler pa
    Posts
    1,058
    sure its an ecm motor ?
    Reply With Quote Reply With Quote
  4. 01-05-2013, 12:53 PM #4
    rundawg's Avatar
    rundawg
    rundawg is offline Professional Member*
    Join Date
    Jul 2007
    Location
    Virginia
    Posts
    3,600
    Quote Originally Posted by tech-c2 View Post
    I looked at a friends payne pg9mtav36075abss furnace the other night.
    T = 2 Stage

    V = Variable Speed ECM Blower

    The control board does control the blower "ON" and "OFF" in Heat and Cool modes.

    There are many dip switches on the control board for setting blower speeds. I would find the install manual and make sure it is set up properly, then do some VOM testing, before I'd condemn the board.

    As, Joehvac25 said, we can't go into too much detail in this "OPEN" forum. Apply for Pro membership, you won't be disappointed.
    Instead of learning the tricks of the trade, learn the trade.
    Reply With Quote Reply With Quote
  5. 01-05-2013, 12:57 PM #5
    Joehvac25's Avatar
    Joehvac25
    Joehvac25 is offline Professional Member*
    Join Date
    May 2012
    Location
    Upper Michigan
    Posts
    3,085
    Quote Originally Posted by rundawg View Post
    T = 2 Stage

    V = Variable Speed ECM Blower

    The control board does control the blower "ON" and "OFF" in Heat and Cool modes.

    There are many dip switches on the control board for setting blower speeds. I would find the install manual and make sure it is set up properly, then do some VOM testing, before I'd condemn the board.

    As, Joehvac25 said, we can't go into too much detail in this "OPEN" forum. Apply for Pro membership, you won't be disappointed.
    Ok I was thinking the older Payne single stage secondary killers lol
    Reply With Quote Reply With Quote
  6. 01-05-2013, 01:30 PM #6
    tech-c2
    tech-c2 is offline Regular Guest
    Join Date
    Sep 2005
    Location
    Windsor Ontario
    Posts
    17
    Thanks Guys I have been meaning to go pro I better get on it.
    Reply With Quote Reply With Quote
  7. 01-05-2013, 02:00 PM #7
    Brent Ridley's Avatar
    Brent Ridley
    Brent Ridley is offline Professional Member*
    Join Date
    May 2009
    Location
    Savannah, Ga/H.H. Island, S.C.
    Posts
    743
    It may be in the thermostat settings. Get a pro membership and we will discuss further on the "other side."
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules