DIRECT IGNITION PROBLEM SHOULD BE SIMPLE!

[hkempf]

They need a like button on here like Facebook so you can just say hey I like that

[mason]

Pull the connector off the flame sensor hook one jumper from your meter to the flame sensor and the other to the wire you pulled off of it, fire the system, you should get 0.5 microampers

Do you mean more than 0.5?

Different manufacturers have different minimum microamp requirements. Many units that have clean, undamaged flame sensors will get over 2.0 microamps during operation.

[Milk man]

This unit still broken? Anyone know which furnace he is working on? Has the OP checked in lately?

[timebuilder]

Pull the connector off the flame sensor hook one jumper from your meter to the flame sensor and the other to the wire you pulled off of it, fire the system, you should get 0.5 microampers

Guys, pay attention. This guy is not a tech. Let's not post info for DIY use when search engines index this forum

[timebuilder]

This unit still broken? Anyone know which furnace he is working on? Has the OP checked in lately?

1) Unknown

2) No

3) No

[jpsmith1cm]

Guys, pay attention. This guy is not a tech. Let's not post info for DIY use when search engines index this forum

[jmac00]

ok pal if you can't get this thing going, here is what you need to do (although this is against forum rules, Im going to fix this for you)





1) Make sure the fuel line is plugged in and locked into the receiver

2) squeeze the primer bulb several time til it feels "hard"

3) Pull the choke all the way out

4) grasp the "T" handle on the pull rope and pull with some authority. (you may have to do this several times)

5) this should start it up. If it starts, wait a few seconds and then push the choke all the way in

If it doesn't start, step back three to four feet and kick it as hard as you can, then repeat the process

Lets me know if this helped???

Ok, Im just bust'n your balls, if it didn't start it's probably because of that damn ethanol.....Good luck, have fun

[Joehvac25]

ok pal if you can't get this thing going, here is what you need to do (although this is against forum rules, Im going to fix this for you)





1) Make sure the fuel line is plugged in and locked into the receiver

2) squeeze the primer bulb several time til it feels "hard"

3) Pull the choke all the way out

4) grasp the "T" handle on the pull rope and pull with some authority. (you may have to do this several times)

5) this should start it up. If it starts, wait a few seconds and then push the choke all the way in

If it doesn't start, step back three to four feet and kick it as hard as you can, then repeat the process

Lets me know if this helped???

Ok, Im just bust'n your balls, if it didn't start it's probably because of that damn ethanol.....Good luck, have fun

I have seen the primer balls go bad, if it won't fire replace the primer ball and try it then, hope I don't get banned.

[jmac00]

I have seen the primer balls go bad, if it won't fire replace the primer ball and try it then, hope I don't get banned.

good call, I forgot about that, gezzz I think we are borderline with this DIY stuff

[timebuilder]

ok pal if you can't get this thing going, here is what you need to do (although this is against forum rules, Im going to fix this for you)





1) Make sure the fuel line is plugged in and locked into the receiver

2) squeeze the primer bulb several time til it feels "hard"

3) Pull the choke all the way out

4) grasp the "T" handle on the pull rope and pull with some authority. (you may have to do this several times)

5) this should start it up. If it starts, wait a few seconds and then push the choke all the way in

If it doesn't start, step back three to four feet and kick it as hard as you can, then repeat the process

Lets me know if this helped???

Ok, Im just bust'n your balls, if it didn't start it's probably because of that damn ethanol.....Good luck, have fun

Holy cow. I was a go-kart kid when I was 11, and that sure brought back some memories!!

BTW, Sta-Bil makes a fuel treatment to mitigate the effects of methanol in gasoline powered equipment.

[koolkahuna]

I see where I've been going wrong. I always start with a Happy Gilmour style kick!

[ryan1088]

I see where I've been going wrong. I always start with a Happy Gilmour style kick!

This is only appropriate if you use the "HIIII-YAAAA" method.

[jmac00]

This is only appropriate if you use the "HIIII-YAAAA" method.

that only works if your using Hy-Karate deodorant

[koolkahuna]

Got it.

Now I'm working' on the battle cry. Heehaw.. Hihowareya...Hallelujah...HiuuYaaa!

[jmac00]

BWHAHAHAHAHA

[timebuilder]

http://www.youtube.com/watch?v=jtwh3nQP5Uo

[CashnHavoc]

What has this guy been doing at work the last 4 years? Who's paying him????

[Mike19]

About one every couple months I go into United and there will be a guy like this in there, all pi**ed off, telling the guy at the counter that all the parts they sell are a piece of s***, because he has changed the gas valve three times and every one was defective, because the burners still wouldn't light even after he put the new one in.

Usually they are always guys in business for themselves.

[2sac]

Well, this thread has really gone for a loop.

[jmac00]

What has this guy been doing at work the last 4 years? Who's paying him????

Installing dishwashers