Page 1 of 6 123456 LastLast
Results 1 to 13 of 72
  1. #1
    Join Date
    Mar 2007
    Posts
    3,071

    Another Chiller Teardown & Rebuild

    770 ton Trane CVHF, bearing failure and a worn oil seal

    Name:  1.jpg
Views: 1304
Size:  53.6 KB
    Removing the economizer

    Name:  2.jpg
Views: 1229
Size:  39.5 KB
    Economizer sealed up for storage to prevent rust

    Name:  3.jpg
Views: 1192
Size:  46.8 KB
    Rigging of suction elbow

    Name:  4.jpg
Views: 1113
Size:  44.2 KB
    Removing suction elbow

    Name:  5.jpg
Views: 1091
Size:  40.1 KB
    Suction elbow covered to prevent rust

    Name:  6.jpg
Views: 1108
Size:  45.2 KB
    Compressor and evaporator flanges covered to prevent rust and prevent debris from falling in

    Name:  7.jpg
Views: 1067
Size:  54.2 KB
    Preparing to remove suction cover

    Name:  8.jpg
Views: 1086
Size:  48.5 KB
    Removing suction cover

    Name:  9.jpg
Views: 1115
Size:  49.0 KB
    Rigging the suction cover down and a shot of one of the work-tables where all of the tools return when we are done with something

    Name:  10.jpg
Views: 1148
Size:  29.7 KB
    Checking the run-out of the 1st stage impeller
    "There is no greater inequality than the equal treatment of unequals."

    -Thomas Jefferson

  2. #2
    Join Date
    Mar 2007
    Posts
    3,071
    Name:  11.jpg
Views: 727
Size:  63.1 KB
    This is where the inter-stage shaft seal mounts on the 1st stage diffuser

    Name:  12.jpg
Views: 729
Size:  42.6 KB
    Looking at the motor journal bearing support with the oil seal, mounting plate, and internal oil line removed

    Name:  13.jpg
Views: 753
Size:  40.6 KB
    Setting up the dial indicator to make sure we do not move the shaft too much when we remove the bearing and bearing support

    Name:  14.jpg
Views: 736
Size:  48.0 KB
    Another shot of the dial indicator setup

    Name:  15.jpg
Views: 824
Size:  40.5 KB
    The failed journal bearing

    Name:  16.jpg
Views: 751
Size:  38.8 KB
    Dowel pins installed to make sure the bearing support goes back exactly where it was before

    Name:  17.jpg
Views: 754
Size:  41.9 KB
    Removal of bearing support - we monitored the shaft at all times with the dial indicator as it could move no more than .003" in any direction

    Name:  18.jpg
Views: 739
Size:  41.2 KB
    Another shot of the removed journal bearing support and the bad back oil seal

    Name:  19.jpg
Views: 794
Size:  34.0 KB
    Inside the motor

    Name:  20.jpg
Views: 769
Size:  53.9 KB
    Last edited by Tech Rob; 10-29-2012 at 10:23 PM.
    "There is no greater inequality than the equal treatment of unequals."

    -Thomas Jefferson

  3. #3
    Join Date
    Jul 2006
    Location
    Anytown USA
    Posts
    2,043
    Something wrong with the second post, I cant see the pictures, first post is ok.

  4. #4
    Join Date
    Mar 2007
    Posts
    3,071
    Quote Originally Posted by y7turbo View Post
    Something wrong with the second post, I cant see the pictures, first post is ok.
    Fixed. This new site format is glitchy.
    "There is no greater inequality than the equal treatment of unequals."

    -Thomas Jefferson

  5. #5
    Join Date
    Jul 2006
    Location
    Anytown USA
    Posts
    2,043
    Quote Originally Posted by Tech Rob View Post
    Fixed. This new site format is glitchy.
    Works now, Thanks for sharing.

  6. #6
    Join Date
    Mar 2007
    Posts
    3,071
    Quote Originally Posted by y7turbo View Post
    Works now, Thanks for sharing.
    Thanks for checking it out and commenting!
    "There is no greater inequality than the equal treatment of unequals."

    -Thomas Jefferson

  7. #7
    Join Date
    Jul 2006
    Location
    Anytown USA
    Posts
    2,043
    Any idea on what the weights were on the parts you removed?

  8. #8
    Join Date
    Mar 2007
    Posts
    3,071
    Economizer 840#
    Suction elbow 700#
    1st vane assy. 400#
    Suction cover 1700#
    Inter-stage 2000#

    Also a couple of smaller items between 50# and 200#
    "There is no greater inequality than the equal treatment of unequals."

    -Thomas Jefferson

  9. #9
    Join Date
    Jul 2009
    Location
    Columbia, MD
    Posts
    3,384
    that is cool! it looks like you know what your doing

  10. #10
    Join Date
    Mar 2007
    Posts
    3,071
    Thanks! My motto is "fake it until you make it"!!!
    "There is no greater inequality than the equal treatment of unequals."

    -Thomas Jefferson

  11. #11
    Join Date
    Jul 2006
    Location
    Anytown USA
    Posts
    2,043
    Quote Originally Posted by Tech Rob View Post
    "fake it until you make it"!!!

  12. #12
    Join Date
    Oct 2005
    Location
    Phoenix, Arizona
    Posts
    340
    Wow. thanks for sharing the pics. I would love to do a tear down like that. nice job!
    RTFM!!!

  13. #13
    Join Date
    Aug 2009
    Location
    Prattville, Alabama
    Posts
    1,749
    I've never seen that bearing bracket removed while the motor is still mounted to the discharge volute. Do you plan to replace the motor-to-volute o-ring? How about the discharge volute-to-condensor o-ring? Appreciate the pics. Very nice equipment room... once you get past the chilled water lines above the starter.

Page 1 of 6 123456 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event