Results 1 to 9 of 9
  1. #1
    Join Date
    May 2007
    Location
    Denver, Colorado, United States
    Posts
    38

    Honeywell Stryker - Who else has had the pleasure?

    So far we've got a few of the VAV with and VAV w/o actuators in and blinking, who else has had the pleasure of installing some of these albino spyders?

  2. #2
    Join Date
    Nov 2006
    Location
    Desert Southwest
    Posts
    726
    Waiting for at least the second rev to show. LOL
    If you can't fix it with JB Weld, Duct Tape, and Ty Wire it has to be replaced.
    No good deed goes unpunished.
    If you want to take off friday to go fishing then make sure you train your helper right.

  3. #3
    Join Date
    May 2007
    Location
    Denver, Colorado, United States
    Posts
    38
    But... then you wouldn't get the promotional shirt?

  4. #4
    Join Date
    Nov 2006
    Location
    Desert Southwest
    Posts
    726
    I hear they only come in short so people won't use them to hang themselves.
    If you can't fix it with JB Weld, Duct Tape, and Ty Wire it has to be replaced.
    No good deed goes unpunished.
    If you want to take off friday to go fishing then make sure you train your helper right.

  5. #5
    Join Date
    May 2007
    Location
    Denver, Colorado, United States
    Posts
    38
    You got me.

  6. #6
    Join Date
    Jan 2005
    Location
    USA
    Posts
    1,461
    Have a demo, messed with it a bit. The tool looks just like lonspec. Dont know of the problems yet but it looks pretty strait foreward, like the xl10 its trying to replace. Not sure why they dropped the whole spyder webs theme from it....maybe HW is getting tired of bugs...I know I am.
    "It's always controls"

  7. #7
    Join Date
    Mar 2009
    Location
    Pittsburgh,PA
    Posts
    31
    Class tomorrow. I am assuming they will review it.

  8. #8
    Join Date
    Jun 2011
    Location
    San Diego
    Posts
    4
    Quote Originally Posted by mydogsnameisbob View Post
    So far we've got a few of the VAV with and VAV w/o actuators in and blinking, who else has had the pleasure of installing some of these albino spyders?
    I have VAV Stryker controller installed on my office’s VVT. So far the controller has been working ok.
    HW did a good job on the AX wizard, literature (Configuration, SRB (Know issues)), hardware, ZIO sensors options and config. menus, Etc. There two important know issues that only apply to AX 3.6.31 that were addressed on the latest AX 3.6 maintenance release.

    From my point of view HW did a good job on this product release.

    I did evaluation summary of the Striker VAV for my bosses and I found that the Stryker uses a little bit more component resources than the XL10 VAV controller (based on Stryker module version 1.0.1). I would like to clarify that I am not AX authority, thus please question the outcome of this resource usage test. Here is part of that summary.
    Attached Images Attached Images

  9. #9
    Join Date
    Nov 2008
    Location
    Jackson, TN
    Posts
    8
    Remember that the striker is not a spyder. so your not going to be able to coustiomize as much. it is just an xl10 replacement with some configuration. the advatage is that it can use a zio where the xl10 can not. My opinion is stick with a spyder and use vennom if your not comferable with programing yourself. For the money, the spyder just makes more sence.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event