Results 1 to 11 of 11

Thread: Cooltube

  1. #1
    Join Date
    Mar 2004
    Location
    Las Vegas, Nevada
    Posts
    1,647
    Post Likes

    Cooltube

    Okay fellas, anyone played with these yet?
    http://www.cooltube.com/
    The views and opinions posted here are my own. They do not reflect the corporate policies of my employer and will most likely get me fired at some point.

  2. #2
    Join Date
    May 2004
    Posts
    12,501
    Post Likes

  3. #3
    Join Date
    Feb 2008
    Location
    California
    Posts
    2,071
    Post Likes
    I've used one before. It was an a oooooold hussmann salad bar which wasn't designed to maintain temperature requirements by today's standards.

    Installed cool tube, aimed it right at the bottoms of the pans and it's been running great since, no problem maintaining product temperatures below 41*

  4. #4
    Join Date
    Jul 2000
    Location
    Guayaquil EC
    Posts
    10,887
    Post Likes
    These have been talked about here before...as far back as 2004:

    http://hvac-talk.com/vbb/showthread.php?t=59548

    ...and again in 2011:

    http://hvac-talk.com/vbb/showthread.php?t=888172

    So they've been around for a while.

    I can't see how they can cram as much capacity into a given length as compared to a finned coil of the same length.

    How would do you control one with a constant cut-in tstat?

    I see condensate drain issues, too.

  5. #5
    Join Date
    Mar 2004
    Location
    Las Vegas, Nevada
    Posts
    1,647
    Post Likes
    I haven't played with one yet, just saw a flyer at the supply house this morning. Looks to me like it has potential and I'll be looking for an opportunity to try it out.
    The views and opinions posted here are my own. They do not reflect the corporate policies of my employer and will most likely get me fired at some point.

  6. #6
    Join Date
    Feb 2004
    Location
    Western New York
    Posts
    1,106
    Post Likes
    Saw the literature at Jordon Supply... priced out a small one, and they are a couple of times more than a Bohn coil.
    Experience is what you have an hour after you need it.

  7. #7
    Join Date
    Jul 2000
    Location
    Guayaquil EC
    Posts
    10,887
    Post Likes
    Quote Originally Posted by baub View Post
    Saw the literature at Jordon Supply... priced out a small one, and they are a couple of times more than a Bohn coil.
    The cost of the Bohn coil retrofit blows me out of the water 90% of the time, so what's the chances for this one?

  8. #8
    Join Date
    Nov 2010
    Location
    MN
    Posts
    147
    Post Likes
    Pretty sure the health dept. around my neck of the woods wouldn't go for it.

  9. #9
    Join Date
    Mar 2004
    Location
    Las Vegas, Nevada
    Posts
    1,647
    Post Likes
    Quote Originally Posted by PMARS2345 View Post
    Pretty sure the health dept. around my neck of the woods wouldn't go for it.
    Why?
    The views and opinions posted here are my own. They do not reflect the corporate policies of my employer and will most likely get me fired at some point.

  10. #10
    Join Date
    Jan 2008
    Location
    Lake Worth, FL
    Posts
    111
    Post Likes

    Smile

    I've dealt with them before. Durable and well built. Won't succumb to corrosion from food vapors over time like others. Axial fans on the end it they go bad - simple to replace. Movable vents to more precisely direct air flow.

  11. #11
    Join Date
    Jul 2005
    Location
    Southern California
    Posts
    605
    Post Likes
    Worked on them when I used to do resturants. They worked well salad bars and on cook prep lines.
    Knowledge is knowing that a tomato is a fruit. Wisdom is knowing not to put it in a fruit salad.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Quality Home Comfort Awards