Results 1 to 11 of 11
Thread: Signal generator?
02-23-2012, 07:38 PM #1
Does anyone use a signal generator? I'm not a control guy and I don't have a laptop. I want to be able to easily test actuators and such without having to call a control guy or mess with setpoints. I fould one on Kele but I was hoping to not spend this much.
02-23-2012, 07:50 PM #2Regular Guest
- Join Date
- Dec 2011
02-23-2012, 08:02 PM #3
Does everything I need it to do.UA LU189
10mm, because it's better than .45acp
02-23-2012, 09:03 PM #4
I have one made(or labelled by) jci ill post the model tomorrow its at the shop
Sent from my SPH-D710 using Tapatalk
02-24-2012, 04:13 PM #5
guess I'll have to bite the bullet and spend some dough. I wonder why that dwyer is SO much cheaper....
02-24-2012, 04:32 PM #6Professional Member
- Join Date
- Mar 2010
- Southeast Michigan
I use the Dwyer ASG had it a year know works good only $150.00.
02-24-2012, 04:45 PM #7
I use this testing millivolt valves:
02-25-2012, 02:12 PM #8
Sorta like the old catalogs from johnstone and cc dickson...... those prices in there are higher than what you are going to pay.....sometimes 40-50 percent higher. Guess it keeps a potential customer from getting hold of a catalog and seeing what you paid for a part or something.
You can use a 9 volt battery for checking 0-10 volts and you can add a potnetiometer for a voltage divider circuit to modulate the output.... there is a thread in the controls section....
go to radio shack and get the stuff you need..... some really simple and easy to build ones on down thru the thread. The one that says panic mode is a good one but requires more stuff.... I wouldnt try and build one using radio shack as a source for the parts.
But the simple designs will work for what you want and probably contain parts that are easily found at radio shack. You might have to buy an assortment of resistors that you will never use again....but its going to be a whole lot cheaper than buying something ready made.
Ive built the panic mode model before and a few simpler designs but I wont use them on the job for fear of a customer seeing me use some cobbled up device on their expensive equipment.
While these devices do pretty much the same thing as a 300-600 or more calibrator..... most customers dont know that.....and they wont bat an eye at you using an expensive store bought device to test their equipment....but when they see you using something you built at home...and 2 weeks later they are looking at some problems with the equipment.... they might come back on you and your device as an easy target for blame.
03-01-2012, 06:06 PM #9
Check with Mitchell Instruments, they have a line of process loop calibrators.
I picked up one of their low end units, $400, and it works great to provide either a 0-10V or 4-20 ma signal.
You can use it in place of an analog signal from a ddc system to troubleshoot and verify proper operation of a device, vfds, modulating valves and burners, damper actuators, electro-pneumatic transducers, etc.When the going gets weird, the weird turn pro. HST
03-10-2012, 12:26 AM #10Professional Member
- Join Date
- Nov 2002
I have the one in the first link, don't think I payed more than 100.00 - 150.00 max at a local controls distributer. Had it for about three years.
04-23-2012, 09:36 AM #11Professional Member
- Join Date
- Aug 2006
Programmable signal generator (PSG) https://www.alpscontrols.com/Prod_Data/ACT/psg.pdfEnjoy your day!