Search:

Type: Posts; User: superfittertech

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. sounds like you're "sucking in" hot humid attic...

    sounds like you're "sucking in" hot humid attic air. I'd get the installing contractor to come back and check
  2. Replies
    35
    Views
    537

    are both furnace blowers running in the correct...

    are both furnace blowers running in the correct direction? I've seen that setup before. On startup (1) furnace fan starts slightly before the 2nd and when the 2nd one starts the wheel is spinning...
  3. If was my own house I'd repair the module (much...

    If was my own house I'd repair the module (much cheaper) 9 times out of 10 the motor is not the problem
  4. Replies
    7
    Views
    275

    shut off power try also replacing the base. If...

    shut off power try also replacing the base. If you have the same stat, should be wire for wire. Make sure jumper between r & rc is installed & make sure you didn't bend any of the pins
  5. Replies
    7
    Views
    275

    you need to call the company explain all of this...

    you need to call the company explain all of this and ask for a different tech
  6. A variable speed motor is not so much about...

    A variable speed motor is not so much about efficiency as it is for comfort
  7. Run Forrest run

    Run Forrest run
  8. Replies
    24
    Views
    600

    there should still be a wiring diagram on the...

    there should still be a wiring diagram on the blower door
  9. Replies
    24
    Views
    600

    the fusable link is a furnace safety wired in...

    the fusable link is a furnace safety wired in series with the main limit switch. If either one is open you will have no 24v at the board and nothing will work! The limit switch will open when too hot...
  10. Replies
    24
    Views
    600

    obviously you aren't a 8 year service tech or you...

    obviously you aren't a 8 year service tech or you would know what I was talking about. Get help from a co worker if you are or go to a DIY website if im guessing right that you are not
  11. Replies
    24
    Views
    600

    fusable link?

    fusable link?
  12. you wouldn't believe how many times project...

    you wouldn't believe how many times project managers have asked me that
  13. if you're using the EIM module then you're ok as...

    if you're using the EIM module then you're ok as you'll still have the humidification options even with the TH8320R1003. The Honeywell C7189R1004
    Wireless Indoor Sensor has built in humidity sensor,...
  14. Holy **** if you're very concerned about that...

    Holy **** if you're very concerned about that very very small amount of air, then be anal and also install an access fitting, then use a vacuum pump to remove air before reopening. Me I wouldn't...
  15. use 2 pinch off tools one on each side of drier,...

    use 2 pinch off tools one on each side of drier, cut out drier, replace with new & braze in. Then open lines back up. Very simple & fast
  16. Replies
    17
    Views
    726

    probably happens when coming out of defrost

    probably happens when coming out of defrost
  17. short answer yes. Have used the thermostat for...

    short answer yes. Have used the thermostat for humidification, however you will also need to have a wireless outdoor sensor installed for window moisture
  18. Replies
    45
    Views
    1,663

    DIY is do it yourself. Did u even read the rules...

    DIY is do it yourself. Did u even read the rules before posting? Call a professional
  19. Replies
    45
    Views
    1,663

    not a DIY site

    not a DIY site
  20. adding return/supply good idea, adjusting gas...

    adding return/supply good idea, adjusting gas pressure (especially down is a very bad idea). Gas pressure should be adjusted by what mfr specs says and with a combustion analyser
  21. Replies
    14
    Views
    494

    did on my own unit although coil was uncased...

    did on my own unit although coil was uncased Furnace Gibson 80,000 BTU 92% 21" wide x 19" deep. ADP coil 18" wide x 20" deep/
    Mounted coil with connections coming out right side. Did this 8 years...
  22. I used a pinch off tool to braze in an access...

    I used a pinch off tool to braze in an access fitting on a liquid line factory charging tee on a R-410 Magic Pac unit with no problems
  23. Replies
    43
    Views
    1,146

    even if u could get it that low 67 will usually...

    even if u could get it that low 67 will usually ice up your coil and possibly slug the compressor. If you need it that low then you have a humidity problem. the lower your humidity the higher you can...
  24. hello did you read previous threads. Did you...

    hello did you read previous threads. Did you change out the liquid line drier?
  25. Replies
    71
    Views
    1,377

    put MP-66 (R401B) in it. Runs slightly above 0...

    put MP-66 (R401B) in it. Runs slightly above 0 psi at -20 degrees
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event