Search:

Type: Posts; User: controltec

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    281
    Views
    40,924

    jjcontrols I sent you an email with a link - -...

    jjcontrols I sent you an email with a link

    - - - Updated - - -

    Bels if you send me an email I will send you a link
  2. Replies
    281
    Views
    40,924

    Skwsproul you've got mail Chad419 you don't...

    Skwsproul you've got mail

    Chad419 you don't have any email address shown in your profile. I will send you the link if you shoot me an email.
  3. Replies
    3
    Views
    291

    underneath the weatherservice object open the...

    underneath the weatherservice object open the weatherreport object. You will then see an object named provider. this is assuming everything was left at default names and not renamed when you setup...
  4. Replies
    281
    Views
    40,924

    akdb2004 is see your from fairbanks. We have...

    akdb2004 is see your from fairbanks. We have taken over the kodiak USCG base from CCI. If your working on network 8000 in that area I'm sure CCI had something to do with it. We have been going...
  5. Special Barber Colemen Siebe Global Control Module SIM-MTECH

    I went to a JCPenny's store today because we were asked to work on an old network 8000 system that wasn't functioning correctly. What I found was something that I had never run into before. The GCM...
  6. Replies
    6
    Views
    621

    We use B&B Electronics for the serial converters...

    We use B&B Electronics for the serial converters that you need. Depending on where you are going to connect to the system there are two different converters that you will need. USOPTL4 for direct...
  7. Replies
    281
    Views
    40,924

    For those who have email address attached to the...

    For those who have email address attached to the profiles I sent you the link.

    jfelty......I don't know how to send it to you there is no address in you profile. You can shoot me an email...
  8. Replies
    281
    Views
    40,924

    I sent you an email with a download link. Enjoy!

    I sent you an email with a download link. Enjoy!
  9. have you made sure that the asd.jar file is in...

    have you made sure that the asd.jar file is in the server too? We have had this issues with other things like the spyder tool. Once we loaded all the spyder tool jar files on the server everything...
  10. Replies
    281
    Views
    40,924

    was the signal installed on a prior system and...

    was the signal installed on a prior system and then the image moved over to another computer or something? Or is it running on the original computer that it was installed on.

    Are you using Signal...
  11. Replies
    281
    Views
    40,924

    have you tried First: super last: user pass:...

    have you tried

    First: super
    last: user
    pass: pass
  12. try this jay.stark at sign bssi.bz

    try this jay.stark at sign bssi.bz
  13. PoleJunk send an email to my email address...

    PoleJunk

    send an email to my email address listed in my profile and I will send you what I have. We use those B&B connectors all the time so it should work just fine. I would bet it is the...
  14. Replies
    281
    Views
    40,924

    CoolingTower You've got mail. I sent you a...

    CoolingTower

    You've got mail. I sent you a link to download all that I have. If you need any help let me know!
  15. Replies
    281
    Views
    40,924

    sure we use a ASD driver for this. Works really...

    sure we use a ASD driver for this. Works really well. We have probably integrate over 50 sites like this. The driver will also allow you to still use the PSI software and tunnel down through the...
  16. Replies
    281
    Views
    40,924

    Jaceski I sent you an email with a download...

    Jaceski

    I sent you an email with a download link.
  17. Replies
    281
    Views
    40,924

    Julip360 I sent you a link for a download of...

    Julip360

    I sent you a link for a download of all that I have.

    Enjoy!
  18. Control Man You have solidified my point. You...

    Control Man

    You have solidified my point. You have yet again wasted everyone's time including your own to post something that completely meaningless. I must have missed something big in the...
  19. tsmsp99 If you email me from my email in my...

    tsmsp99

    If you email me from my email in my profile I will send you a link to download all the stuff that I have.
  20. 352131

    352131
  21. I really don't know why you would waste your time...

    I really don't know why you would waste your time or anyone else's time to respond to a forum and not contribute anything of value. For your information I copied this right out of the user manual,...
  22. the GCM is the Global Control Module. this is...

    the GCM is the Global Control Module. this is the master brain behind a network 8k system. This you can access with hyperterminal or XPSI software. The XPSI is in the download that I sent you. ...
  23. Gatertech I will email you a link to download...

    Gatertech

    I will email you a link to download the manuals that I have. You don't need any special software for the LCM's they are just a RS-232 interface with hyperterminal. If the LCM isn't...
  24. Replies
    281
    Views
    40,924

    hyperterminal settings will vary depending on...

    hyperterminal settings will vary depending on what was setup in the GCM. Usually 8 none and 1 with a 9600 baud works just fine. You will need a 9 to 25 pin serial cable. Depending on the type of...
  25. mrmonsterpants you've got mail. Let me know...

    mrmonsterpants

    you've got mail. Let me know if you need any help.
Results 1 to 25 of 64
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event