Search:

Type: Posts; User: pcp

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. If you remove all low voltage and still have...

    If you remove all low voltage and still have power at O you have a jumper to cut.
  2. Just replaced a board in a lennox furnace that...

    Just replaced a board in a lennox furnace that flashed polarity code even though polarity was not reversed. Noticed that it too had power at O on a heat pump system. Installed new board and furnace...
  3. Replies
    57
    Views
    2,523

    What did the other techs at your shop say?

    What did the other techs at your shop say?
  4. The h10 is used exclusively at our company now...

    The h10 is used exclusively at our company now and dyes are no longer used. Very worth it.
  5. Thread: Cutting Plaster

    by pcp
    Replies
    33
    Views
    1,014

    When cutting round holes through a ceiling, cut a...

    When cutting round holes through a ceiling, cut a basketball in half put a hole in the ball for the drill bit then put it between the hole saw and the drill. It will catch everything and keep dust...
  6. Thread: pressure issues

    by pcp
    Replies
    6
    Views
    374

    Go to school and have someone beat it into your...

    Go to school and have someone beat it into your head. It's the easiest way.
  7. Replies
    47
    Views
    1,803

    Tmi. Imo

    Tmi. Imo
  8. Replies
    23
    Views
    1,077

    Is the heat pump found. Is it a communicating...

    Is the heat pump found. Is it a communicating heat pump.
  9. Your buddy must hate you I know I would.

    Your buddy must hate you I know I would.
  10. Replies
    4
    Views
    494

    If it opens on limit in one stage it will run in...

    If it opens on limit in one stage it will run in another stage and may not lose temp. Don't assume nothing is wrong though. These limits are touchy and the furnace can run very close to limit temp
  11. Replies
    16
    Views
    765

    Look at the plug from the front not the back and...

    Look at the plug from the front not the back and see if it makes more sense.
  12. Replies
    7
    Views
    344

    I think I did one of these a couple years ago and...

    I think I did one of these a couple years ago and I think you might be looking at the plug from the wrong direction.
  13. Thread: On Call Incentive

    by pcp
    Replies
    58
    Views
    4,482

    We get $150 for the week, 1.5 time port to port...

    We get $150 for the week, 1.5 time port to port and $25 per call. All companies should charge enough to make it worth while for the technician to give up there time.
  14. Replies
    15
    Views
    1,073

    It helps expose gas valves and inducers to...

    It helps expose gas valves and inducers to moisture and they sell more parts.
  15. Replies
    14
    Views
    2,682

    Easiest to pull the burner box unless the...

    Easiest to pull the burner box unless the installer glued in the combustion pipe. Company I work for has a lot out there where they glued in street 90s
  16. Thread: problem customers

    by pcp
    Replies
    48
    Views
    3,968

    How much does it cost to buy an egg at the...

    How much does it cost to buy an egg at the grocery store and why is it so much more at a restaurant? People just don't think.
  17. Is there a link to Carrier's memo? I can't find...

    Is there a link to Carrier's memo? I can't find it.
  18. Think you would need a nim control to do this.

    Think you would need a nim control to do this.
  19. Do you work for honeywell? I'm not a fan of nest.

    Do you work for honeywell? I'm not a fan of nest.
  20. Try putting cork pads under blower housing if its...

    Try putting cork pads under blower housing if its a vibration issue.
  21. Replies
    7
    Views
    874

    Bryant 383 has same HX.

    Bryant 383 has same HX.
  22. Replies
    7
    Views
    874

    Yes you can see them with the blower out. The...

    Yes you can see them with the blower out. The dimples by the limit seem to be the last to crack, and they crack if the baffles are there or not, smaller units don't have the baffles.
  23. Replies
    1
    Views
    353

    That's the model number for your evaporator coil.

    That's the model number for your evaporator coil.
  24. Replies
    13
    Views
    1,367

    Pretty sure it dosent work because you need the...

    Pretty sure it dosent work because you need the other head to act as an accumulator. The unit recognized only one head is hooked up.
  25. Replies
    16
    Views
    1,109

    Mushroom the shaft?

    Mushroom the shaft?
Results 1 to 25 of 82
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event