Search:

Type: Posts; User: $_aei

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    825

    If it works on the bench it has to be the location.

    The problem could be electrical, I would check for proper voltage and also check the neutral conductor. If it works on the bench it has to be the location.
  2. Thread: my new van

    by $_aei
    Replies
    63
    Views
    19,291

    Nice Van.

    Wish I could just keep mine as neat.:o
  3. Replies
    17
    Views
    5,413

    Nice

    Nice... Weathered pretty good
  4. Thread: Old Units

    by $_aei
    Replies
    6
    Views
    869

    Thanks

    Thats pretty much what I've been doing when time allows,
    Kinda sad that a CrackHead will destroy a condenser for 30 or 40 dollars, Even less than that if they get a spiral tube.
  5. Thread: Old Units

    by $_aei
    Replies
    6
    Views
    869

    Old Units

    How do you dispose of old units, Do you remove coils, copper ect, or just scrap them in one piece? how much difference does it actually make?
  6. Thread: The Buttocks

    by $_aei
    Replies
    2
    Views
    1,355

    Funny

    :)
  7. Replies
    5
    Views
    1,791

    Love the one about the Gorilla's

    Big Fingers, I kinda think the Gorilla's not the only one with that problem.:rolleyes:
  8. Replies
    12
    Views
    3,657

    an OOgiee gone bad

    Kinda like an OOgiee gone bad..... like without any women.:eek:
  9. Replies
    17
    Views
    4,031

    Darn

    I never saw anything quite like that...
  10. Thread: Sizing Question

    by $_aei
    Replies
    1
    Views
    601

    Sizing Question

    Is it Standard Practice to upsize the Indoor coil & Air Handler by 1 ton??
    3 ton outside, 4 inside heatpump
  11. Replies
    8
    Views
    3,953

    What....

    People make fun off what they don't understands...:rolleyes:
  12. Replies
    25
    Views
    4,261

    Thats Sad

    :eek:
  13. Thread: An epic question

    by $_aei
    Replies
    29
    Views
    2,414

    Simpler is better..

    How much to you actually save.... you can by more efficent equipment but how far down the road is the break even point when compaired to simpler systems.... For my money simpler is always more...
  14. Replies
    16
    Views
    1,526

    Mastic Tape?

    I'm sure most of you are talking about Mastic Tape,...Very easy to work with and extreamly difficult to remove, an excellent product.
  15. Replies
    15
    Views
    1,386

    Could be bad..

    Valves not seating properly, Vibration
  16. Replies
    44
    Views
    3,342

    Thinner = less expensive to build.

    You ever heard of enhansed copper?
  17. Replies
    44
    Views
    3,342

    Whatever...

    Some manufactures make tons of money with people assuming that you get what you pay for, Just because it cost more doesn't make it any better. In fact you be surprised how cheeply some " Top Shelf "...
  18. Replies
    18
    Views
    1,542

    Never around

    You mean the ones that are never around to do any service work???:(
  19. Replies
    18
    Views
    1,542

    Changed the return..

    I changed the Return @ 1st Failure, I'm not going to knowing leave a problem with any unit unless the HO just refuses my advice. I just want to be as certain as I can that its not something I may...
  20. Replies
    18
    Views
    1,542

    ??

    I didn't install this unit , just ended up with it . The unit is a 12 seer Gibson Heat pump. I'm not certain why the unit was replaced, HO said they replaced line sets , really didn't look that way...
  21. Replies
    18
    Views
    1,542

    filter in the vapor line

    I have never seen a filter in suction line, The unit seems to have a bad bearing in the compressor, would any debree that happens to make it throught the accum. cause bearing failure?
  22. Replies
    18
    Views
    1,542

    Compressor Failure

    Replaced compressor and Reversing valve on 3 ton Gibson. Pilot line broke off on valve and compressor shorted starting with no R-22. Now 2 mos later the compressor sounds like it has a mouth full of...
  23. Replies
    31
    Views
    4,639

    How about a good cleaning

    That coil is kinda dirty, not that it needs and extra pressure to lose the Freon.
  24. Replies
    20
    Views
    2,904

    Steve O

    That one dude kinda looks like Steve O
  25. Thread: Forms

    by $_aei
    Replies
    1
    Views
    571

    Google

    You can buy them on the Net.
  26. ???

    You should change both with a matched pair.
  27. Replies
    223
    Views
    10,043

    Poll: Always

    I'm kinda shocked that everyone doesn't
  28. Not so Fast...

    I would venture to Say your problem is electrical, and not with the size of the unit or duct work.
  29. Replies
    14
    Views
    1,601

    Thats my trouble not enough post, I would also...

    Thats my trouble not enough post, I would also agree on not undervalueing yourself, I kinda dought very many people don't make it because they charged too much.
  30. Thread: 1000 words

    by $_aei
    Replies
    13
    Views
    3,662

    Hard to polish a

    Well you know....
  31. Replies
    20
    Views
    4,519

    You don't see that very often

    Nice, :eek:
Results 1 to 31 of 38
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event