Search:

Type: Posts; User: ruth32

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: Ok, Robo

    by ruth32
    Replies
    20
    Views
    1,524

    Alberta! I gotsa beat, I have been in the...

    Alberta!
    I gotsa beat, I have been in the business sence 1955.
    I am not sahmed of either. I have seen a lot of changes. You are soooooo right
    ROBO does seem to know his stuff. I for one am going...
  2. Thread: Portland.

    by ruth32
    Replies
    12
    Views
    858

    Norm you are right! Everyone of our installers...

    Norm you are right!
    Everyone of our installers have to hold a Low voltage liscens Just to get a permit. Thats right folks we have to pull a low voltage permit with a Mech. permit. A permit to run...
  3. Thread: Portland.

    by ruth32
    Replies
    12
    Views
    858

    They were probley all from California too.I have...

    They were probley all from California too.I have been in OR. for about 30 years, And I have meet very few native Oregonians.Most of us came up here from CA.
    I too am a trans planted Californian, and...
  4. Replies
    14
    Views
    1,345

    When I go on a service call on a oil furnace I...

    When I go on a service call on a oil furnace I make sure the flue is not blocked with sute. it is a must that it is clear. pull the burner assy out and clean the electrodes, set the gap, in stall a...
  5. Thread: In conc. Slab

    by ruth32
    Replies
    4
    Views
    674

    PVC coated spiral pipe. OK I'll try that. Thanks...

    PVC coated spiral pipe. OK I'll try that.
    Thanks a lot tinner!
  6. Thread: In conc. Slab

    by ruth32
    Replies
    4
    Views
    674

    Question, has anybody out there installed supply...

    Question, has anybody out there installed supply duct in conc. slab latley, in a home.
    It's been sometime sence we have installed duct under slab.we have a gen. contractor that wonts us to install...
  7. Replies
    20
    Views
    1,632

    I got locked in walk in freezer once for about 10...

    I got locked in walk in freezer once for about 10 min.
    the dam push rod on the door broke off in side the door. and all I had was a little pissie ass screw driverin my pocket.
    All I could do is...
  8. That a boy ROBO!!!!! you said it.I have...

    That a boy ROBO!!!!!
    you said it.I have installed a lot of 80's & 90's
    and never had a bad heat exchanger.
    like mentioned before, the equiptment is only as good as the instellation. Good...
  9. Replies
    20
    Views
    1,827

    What do you think about blocking off part of the...

    What do you think about blocking off part of the condenser, and bring the cond. pressur up to designed conditions say @ 100*, clear the sight glass, check SH and SC with the box at designed...
  10. Thread: FAN CYCLE

    by ruth32
    Replies
    7
    Views
    804

    fan cycle

    OK! it looks like I need to only cycle [1] fan.
    Thanks for your input, very helpfull,thanks again.
  11. Thread: FAN CYCLE

    by ruth32
    Replies
    7
    Views
    804

    on a new low temp cond. unit that was shiped...

    on a new low temp cond. unit that was shiped without a fan cycle control. I didn't notice it untill it was all piped in and ready to go. so old lucky me has to install a fan controle.
    the unit has...
  12. Thread: walk in freezer

    by ruth32
    Replies
    4
    Views
    918

    I am ready to start up a -5* walk in freezer...

    I am ready to start up a -5* walk in freezer tomorrow. a thought!
    is it good practice to bring the freezer down to say +32*
    for the first 24 hours, then +15 the next 24 hours, then
    -5* to help...
  13. Replies
    7
    Views
    1,116

    Good advice. 42yrs exp I too am an old timmer, ...

    Good advice. 42yrs exp
    I too am an old timmer, your just a kid I have 45 years in the trade.
    good to see old timmers posting here.
    42 years? do you see a lot of the trade fading as we all die...
  14. Thread: Sanyo A/C

    by ruth32
    Replies
    1
    Views
    632

    I have a question on a Sanyo 2 ton cond. nunit...

    I have a question on a Sanyo 2 ton cond. nunit mod.#CL2412
    I have no info on it except a washed out wiring diagram.
    is the cond. fan motor a veriadle speed or just a 2 speed?
    from what I can make...
  15. Replies
    17
    Views
    3,177

    Looks good to me too. except, how in the heck are...

    Looks good to me too. except, how in the heck are you gonna sheet rock around everything?
  16. Thread: Superheat

    by ruth32
    Replies
    7
    Views
    795

    Thata my thoughts too.

    Thata my thoughts too.
  17. Thread: Superheat

    by ruth32
    Replies
    7
    Views
    795

    Is it common practice to check SH at the...

    Is it common practice to check SH at the evap.with the fans off. I can remember an old timmer used to do it that way. any comments?
  18. Replies
    29
    Views
    3,064

    That is strange. I think I would start by front...

    That is strange. I think I would start by front seating the king valve, and see if the compresser will pump down to about 5# and stay down. If not that tell you that the compressor is weak, or...
  19. Replies
    9
    Views
    999

    Yes the SH shuld come down as will suc. pressure...

    Yes the SH shuld come down as will suc. pressure as the box tep. gets near to 35*
  20. Replies
    9
    Views
    999

    Iam asuming you wont to run the box at 35* is...

    Iam asuming you wont to run the box at 35* is that right?
    walking coolers normanly run @ 35*.
    that being the case the split between the ciol temp and the box should be about 20*. That means the...
  21. Thread: Defrost times

    by ruth32
    Replies
    7
    Views
    869

    Thanks a lot,Much appreciated.

    Thanks a lot,Much appreciated.
  22. Thread: Defrost times

    by ruth32
    Replies
    7
    Views
    869

    I went on a walkin freezer call today, and found...

    I went on a walkin freezer call today, and found the following. iced up big time.
    found defrost heaters burned out, and the time clock had just been replaced a week ago by one of my competers.
    the...
  23. Replies
    9
    Views
    1,019

    R12rules you said in the old days befroe r12 was...

    R12rules
    you said in the old days befroe r12 was outlawed we could valve of the king valve. pump dawn the unit to check capasity,
    with the new refrigerants we cant do that? where can we find more...
  24. Replies
    17
    Views
    1,291

    Norm . Question, you said to take the CPR...

    Norm .
    Question, you said to take the CPR valve out of the systen unless it uses hot gas defrost. If the valve is removed isent there a chance of slugging the comp. when it comes out of defrost....
  25. Thread: King valve

    by ruth32
    Replies
    27
    Views
    13,599

    Dear Hotsummer! If it is possable in youe area,...

    Dear Hotsummer!
    If it is possable in youe area, join a lacal RSES Chapter.
    lots of good info.
    Harvey Tankersley:
Results 1 to 25 of 32
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event