congratulations! i read your posts everyday,and thanks for your help in the past!!!
Type: Posts; User: fatjack
congratulations! i read your posts everyday,and thanks for your help in the past!!!
Ihave a YORK AFFINITY 8T and my installer told me to wax it twice a year!
I can tell the before and after difference!
more supply ducts are going to be added in the spring,thats for the room furthest from the air handler that has low air supply!not noise.
My blower motor noise is a rumbling noise at start up and a vibration that you can feel by touching the furnace and gas pipe! it only does this at certan speeds,other wise you cant hear the blower at...
hello! My contractor replaced inducer motor,and blower motor complete with new module &blower wheel!the blower motor rumble at start up is still there with vibration at certain speeds.the inducer...
Its noisey at the furnace!,and he checked the dip switch settings!he said he thought the inducer motor had a bearing noise.relacement of blower motor parts is due to vibration.
I have a pc9 also with noise problems! My contractor&York rep just left three hours ago.The factory rep told the contractor to replace the inducer motor,the main blower motor,the blower motor...
I havent had time to deal with the inducer motor problem,been to busy.
will keep you posted.Our temp. here in stlouis has been jumping all over the place,one day 25 next day 49.hard to keep track of...
Beenthere,thank you for your response.Ithink 5 cph,was very hard on my equipment,
The difference between 4-5 cph is unbelieveable,im going to try 3-for three days or so
to see how it does.Ive been...
Sorry about delay! i havent talked top my contractor,but i went ahead and reset my cph
rate to 4.what a difference in my furnace,it is actualy modulating like it should.last night i timed the run...
the furnace only runs on average about 6-7 min.then turns off. and funny you should mention it my installer is coming out to check my inducer motor,when my furnace first starts up and ramps to high...
ryan thank you for the web sight info.the instruction manual says under function number0240 (3 cph used for hot
water systems or high
efficiency (90% or better)
fossil fuel forced air
systems....
The furnace is about 13 months old.It was doing this same thing last year,but i thought maybe it was normal for a modulating furnace.i have been reading post every day like a hobbyfor about a year...
I just looked and the stat is calling for heat,and the furnace is not flashing any trouble codes! I read another post to day that beenthere says a setting at 3 CPH is abetter setting for a york...
as soon as my furnace shuts off,it turns back on again within 10 to 30 seconds some times.
My manual does not give me the function number for cycles per hour!
hello,I would like to check the cycles per hour rate on my thermostat,but i dont know how to get into the installers screen.My thermostat is a visionpro
8321u1006
Myfurnace is a york...
Idont know what the settings are at.must be right though its 77&humidity is39%.
ten year parts & labor +spring &fall check ups.
sorry forgot the thermostat &coil
VISION PRO 8321
FC/PC60C+TXV
Affinity 8T CZE03811
PC9C20N100UP11 -FURNACE
F100F Honeywell media filter 10 merv.
uv200-white rodgers germicidal uv light
General 240humidifier from old furnace but works well.
I also have a new affinity 8T with modulating furnace.i am very happy with it .Its nice & quiet! my electric bill was always higher than my sons who lives across the street from me,now mine is 40...
thanks for your time!
hello! would like to know if someone could tell me the seer rateing of my 22 old wirlpool condenser.
model no.ncab036ab01
mfr numberh-90665465
r.l.a 20.4 l.r.a 89...