Search:

Type: Posts; User: Ammocan

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    458

    Industrial Technician Wanted

    Currently seeking a tenured professional in the Industrial HVAC division of a fortune 500 company.

    Prefer a candidate in the greater Raleigh NC area but be able to work NC and SC
    Relocation...
  2. Replies
    1
    Views
    353

    Winston/Greensboro NC

    Light commercial/pm tech needed for Winston to Greensboro.
  3. Replies
    5
    Views
    1,048

    oil pump will run for about 5 minutes until the...

    oil pump will run for about 5 minutes until the capacitor blows up
  4. Replies
    5
    Views
    1,048

    I already started the machine once to see if it...

    I already started the machine once to see if it would turn and it did turn over but pressure was too high sitting in a hot room for too long. turned on the purge and told them they need a new pump...
  5. Replies
    5
    Views
    1,048

    CVHE-020 capacitor grenade

    I have an CVHE that has been offline for 4 years with the power on and oil is hot. Ran the oil pump first and the start capacitor grenaded within 5 min. checked the relay and it was not stuck...
  6. Replies
    3
    Views
    747

    Been There Done That

    I worked for them around Charlotte several years ago. the office is in Ga. and you send them all your paperwork. I think they track all your time on the computer. It is a good place to work if you...
  7. Replies
    7
    Views
    1,240

    header kit....

    Just a quick question for you but could the header be partially restricted but not freeze up?
    What are some symptoms??

    Thanks.
  8. Replies
    22
    Views
    1,636

    Tubes Fouled

    First off I would double check all temps with a temperature probe. If you still come up with 15 deg approach then brush the tubes.
  9. Replies
    12
    Views
    1,136

    Found something in there

    First of all thanks for all of you're replies and input.
    This response encourages me to participate more on the board.

    A little history on this machine,
    The machine has been leaking for years...
  10. Replies
    12
    Views
    1,136

    CVHE080 Squeelin at me........

    Hello all.

    I do not have any posts but I have been a long time reader here.
    I thought I would share something here and see if I am on the right track and also to see if I would get abused for...
  11. Thread: Screw this

    by Ammocan
    Replies
    11
    Views
    1,628

    Freeq on a screw?

    Dont you think it would have an oil problem if it ran below top speed?? Dunno maybe its just me.
  12. Replies
    8
    Views
    956

    Cold Start

    The differential oil flow is not going to operate with low condenser water (already known)A bypass or flow control is the only reliable way you are going to keep that machine running.
    The fan...
  13. Replies
    3
    Views
    838

    Broken hot gas line

    I have seen this same occurance on cell phone boxes and those bard units. As long as the unit did not run with that line broken and pump all the oil out it should be ok. The unit needs to be triple...
  14. Replies
    20
    Views
    2,629

    Hey you gotta get that lifting plate it will...

    Hey you gotta get that lifting plate it will allow you to lift all sections level and safe also will allow you to go from one chain to the next to get it on the ground. Trust me you need the lifting...
  15. Replies
    11
    Views
    1,184

    First Post

    Hello this is my first post....
    Just wanted to say the sight glass is definately there to check the charge without approach. About like grabbin the suction line on a 2 ton LOL
Results 1 to 15 of 64
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event