Search:

Type: Posts; User: litespeed

Search: Search took 0.00 seconds.

  1. Wow, flame the poster and the contractor in one...

    Wow, flame the poster and the contractor in one fell swoop! If you would have read above, you would have been enlightened in knowing that they explicitly stated they have only installed a few of the...
  2. From what i can tell from looking at the...

    From what i can tell from looking at the honeywell site and finding a similar Trane (American Standard) spec sheet with wiring diagram, all that would be required is the....

    Honeywell part...
  3. I appreciate the input. The contractor in...

    I appreciate the input.

    The contractor in question did do a heat load calc to determine the correct size unit. I have the wrightsoft rightJ output.

    Now, regarding balance point calcs, doesn't...
  4. To comment further, i don't think the HVAC...

    To comment further, i don't think the HVAC contractor i have has done many vision pro installs. They did an excellent job on the hardware installation. This might be a non-issue if that AMerican...
  5. I personally setup the Vision Pro myself while...

    I personally setup the Vision Pro myself while the contractors were gone to lunch and everything is setup fine according to them.

    However, the questions i have above are not covered in the...
  6. Hi all, Just had my unit installed, and i'm...

    Hi all,

    Just had my unit installed, and i'm trying to figure out how the balance pts are set on the following model..

    American Standard WCX030G100 Premium

    I have a vision pro 8000, and was...
  7. Replies
    12
    Views
    1,253

    Thanks for the info, i'll make sure to see if i...

    Thanks for the info, i'll make sure to see if i can bump that up to a variable speed motor unit.

    I definitely want to replace the flex, but not sure i want to deal with that so close to colder...
  8. Replies
    12
    Views
    1,253

    Well, here goes.. Out of five HVAC companies,...

    Well, here goes..

    Out of five HVAC companies, only one guy even mentioned a heat load (j manual) calculation and offered to crawl around with me under the house to check the ducting. One other...
  9. Replies
    12
    Views
    1,253

    Thanks for the replies... Wyounger, i'm...

    Thanks for the replies...

    Wyounger, i'm hailing from Coffee county, Tullahoma to be specific.

    I'm familiar with HP systems, but i'm originally from Southern IL, and they are not as plentiful....
  10. Replies
    12
    Views
    1,253

    Hey, thanks for the post! I was hoping to find...

    Hey, thanks for the post! I was hoping to find some people in the general area for their opinions.

    I've been doing more number crunching using those COP numbers and the number of heating days we...
  11. Replies
    12
    Views
    1,253

    Yeah, i realize the COP values change drastically...

    Yeah, i realize the COP values change drastically relative to temperature, but wasn't sure how to factor that in.

    I would like to go straight electric, but since i'm already setup for gas packs,...
  12. Replies
    12
    Views
    1,253

    I changed the Btu value to reflect a 100%...

    I changed the Btu value to reflect a 100% efficiency compared to the 80% gas pack...
  13. Replies
    12
    Views
    1,253

    Hey all, Currently have a 13 yr old gas pack/...

    Hey all,

    Currently have a 13 yr old gas pack/ AC unit package. 1500 sq. ft. house with 2.5ton unit. THe gas pack just gave up the fight and i need to replace the unti. The automatic control valve...
Results 1 to 13 of 13
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event