Search:

Type: Posts; User: kc-srvs

Search: Search took 0.00 seconds.

  1. Let me clarify a bit... I'm not saying it will...

    Let me clarify a bit... I'm not saying it will do the job of a humidifier. You can see approx 3% increase of humidity, nothing astronomical. I am sure it is because of the fact it IS a contained...
  2. One more for you: ...

    One more for you:

    http://www.aprilaire.com/product.asp?ID=FBEB12213A034BF8B488ADBA514A15E1&categoryID=F16F78145781484A8A7C756B87F43AB3
  3. Steam is produced from hotwater as I'm sure you...

    Steam is produced from hotwater as I'm sure you know. That water in the boiler is anywhere from 180 to 190 degrees when running. Water boils at 212. You still get steam before the boil, just not...
  4. Are you getting nose bleeds? I'm wondering why...

    Are you getting nose bleeds? I'm wondering why you need the Humidifier if you have hotwater heat??? Hotwater heat auto. puts humidity in the air. Maybe whomever installed the baseboard under sized...
  5. Replies
    18
    Views
    2,512

    Was thinking of that, I know there have been a...

    Was thinking of that, I know there have been a few updates since the install... heh, heh. Yes, the pilot did that when I went to adjust it from the original valve, I concluded the valve was bad......
  6. Replies
    18
    Views
    2,512

    Blue Johson Control as you asked. Everything...

    Blue Johson Control as you asked. Everything appears to be in order. Nat Gas for oriface...

    [Edited by kc_srvs on 03-07-2005 at 09:01 AM]
  7. You could possibly switch the tonage on the...

    You could possibly switch the tonage on the blower by replacing it, but you can definatley not up the BTU. I suggest putting a secondary in the attic.
  8. Replies
    8
    Views
    1,019

    Contracts are good depending on how they are...

    Contracts are good depending on how they are written. Some service contracts state that they include parts and Pm's and priority care, etc. it all depends on what you agree to. Just make sure you...
  9. Replies
    96
    Views
    5,833

    Great addition!

    Great addition!
  10. Any time pal!

    Any time pal!
  11. Replies
    12
    Views
    1,075

    Ahhhh! See, I did miss that one beenthere! Yes...

    Ahhhh! See, I did miss that one beenthere! Yes your stat should be for 2 stage. You should just be able to go and purchase a sub base for 2 stage though to modify the stat. I'm assuming the stat...
  12. Replies
    96
    Views
    5,833

    Gentlemen, I think we got a little off topic... ...

    Gentlemen, I think we got a little off topic...




    I also think everyone has established he is new and that his company should be training him. Do you gents remember when YOU were in his...
  13. I would definately replace the board then. If...

    I would definately replace the board then. If voltages are good and your not getting any fault codes stating there is a problem then it comes down to the board sending 120v to the inducer. No doubt...
  14. Replies
    18
    Views
    2,512

    *laughs Yes, I know this. Just never seen it...

    *laughs

    Yes, I know this. Just never seen it before and wondered if anyone else had. Also wondered about the color thing... kinda threw me for a loop when he said it was opposite. Thanks for...
  15. Replies
    18
    Views
    2,512

    pilot is 8" with Inducer running only and same...

    pilot is 8" with Inducer running only and same with blower running.
  16. Replies
    18
    Views
    2,512

    New valve was installed, I checked the gas...

    New valve was installed, I checked the gas pressure = 3.5" W.C., and the flame is yellow/orange - 8" long - and it does roll. I just got thrown when another Tech reversed the colors on me... he is...
  17. Replies
    18
    Views
    2,512

    Just the middle one stays yellow... That is what...

    Just the middle one stays yellow... That is what led me to believe the middle HX was cracked... Then I get this other guy saying I have the colors from the basics mixed up:

    Blue = Normal...
  18. You say the terminal reads 26v... I'm assuming...

    You say the terminal reads 26v... I'm assuming you mean R & W terminals for Stat. What is the voltage off the motor? Unplug it and take a reading across the hot and common while calling for heat. ...
  19. Replies
    12
    Views
    1,075

    Just wondering, what made him determine that the...

    Just wondering, what made him determine that the Stat was on the fritz? If he found a loose wire for constant fan and that fixed the problem they were having......... why replace a Stat that has...
  20. Replies
    18
    Views
    2,512

    Pilot and orifice line is clean, I pulled and...

    Pilot and orifice line is clean, I pulled and cleaned as I checked the spark. I am getting 30v on the ignition and the sensor works great. I'm just mind boggled on that darn 8" flame from the...
  21. Replies
    18
    Views
    2,512

    Ok, first I will say hi to everyone being my...

    Ok, first I will say hi to everyone being my first post.

    Next, I received an emergency call today. When I got there and turned the power back on the furnace, Lennox - MD#G23Q2\3-75-2, the ID...
Results 1 to 21 of 24
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event