Search:

Type: Posts; User: MUNC

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Not a love joy as we know from pumps now adays...

    Not a love joy as we know from pumps now adays but more like a giant version found on glycol transfere pump. kind of a cross looking deal
  2. Climatrol air handler 43years old looking for parts

    Hi all hope someone out there can help. I have a climatrol air handler (cold deck,hot deck) mod. CM-32.00 ser. 13A69N-2.03 that has a two piece blower shaft with a rubber coupling between the two...
  3. Replies
    4
    Views
    697

    Whats the super heat? could the compressor not be...

    Whats the super heat? could the compressor not be getting enough cooling of the windings from the refrig?
  4. Replies
    18
    Views
    2,090

    The thing kinda looks like a new automotive...

    The thing kinda looks like a new automotive fitting huh??? Well last i heard it's for the factory charging and testing as the unit goes down the line, quicker to send the juice in that size...
  5. Replies
    27
    Views
    2,829

    Have had to replace a few txv's on the water...

    Have had to replace a few txv's on the water source pumps at one location in the past. Carrier units
  6. Replies
    15
    Views
    1,942

    Save washed out bearings as oil floats on the...

    Save washed out bearings as oil floats on the liquid refrig. My vote is for cc heat
  7. Replies
    7
    Views
    891

    Exactly where i would have sent him, might add if...

    Exactly where i would have sent him, might add if poss using same static station for both rtu's
  8. Replies
    16
    Views
    1,930

    Fill me in, all I was saying is if your necking...

    Fill me in, all I was saying is if your necking down the 3/8 hose whats the gain? Been pullin from my 3/8 thru manifold to both sides of system for years and get good, fast acurate evacs fine
  9. Replies
    12
    Views
    4,427

    [/COLOR] To achive the -3.5 to -2.5"wc at gas...

    [/COLOR]
    To achive the -3.5 to -2.5"wc at gas valve before valve energized. Then set the -0.2". watch supply pressure 2" to 14" optimal 7" static and during operation shouldnt vary too much.
  10. Replies
    6
    Views
    3,692

    Is this thing a pressurized combustion chamber...

    Is this thing a pressurized combustion chamber that needs the door on and sealed for proper operation? Have you checked the gas pressure( supply) while unit is firing to see if it drops off? ( bugs...
  11. Replies
    16
    Views
    1,930

    Exactly, why even use the 3/8 hose?? It's for the...

    Exactly, why even use the 3/8 hose?? It's for the four port man.
  12. Replies
    8
    Views
    1,722

    Frickin funny. Things people do. See much of the...

    Frickin funny. Things people do. See much of the same up this way
  13. Thread: racing work vans

    by MUNC
    Replies
    25
    Views
    1,563

    Two techs i worked with back in Chicago where...

    Two techs i worked with back in Chicago where racing down I294, long story short lead guy started to lose his ladder and jammed on the breaks second guy didn't stop. Results??? Two totalled service...
  14. Replies
    5
    Views
    634

    Serviced a place the maintenance crew was using...

    Serviced a place the maintenance crew was using the diconnect to cycle a pump. The thing got so worn out it would miss a "knife" from time to time and single phase the pump. The H.O.A. switch for the...
  15. Replies
    12
    Views
    4,279

    Valves,unloader????. you amp compressor? have had...

    Valves,unloader????. you amp compressor? have had bad comps out of the box, but rare. drier, liquid line sol? start from the beginning and happy hunting
  16. Replies
    12
    Views
    4,427

    Have had quite a few stuck tco's. Make sure to...

    Have had quite a few stuck tco's. Make sure to measaure and compare delta 't' to find why the tco tripped to energize fan circuit and get stuck there. Filters,belt,dampers,bypass ducted too close to...
  17. Replies
    4
    Views
    12,371

    Could be zone averaging with all the stats,...

    Could be zone averaging with all the stats, oooorrrrrr that old, how bout poss wheatstone bridge
  18. Replies
    13
    Views
    1,133

    If this thing didn't have a low # cut out and...

    If this thing didn't have a low # cut out and lost the juice prob fragged the comp.
    no pumpin means no suction cooling thus " hot comp". If service valves, try pumpin it down, amp it and listen. if...
  19. Real nice to have trend logs of bearing temp and...

    Real nice to have trend logs of bearing temp and oil sample results
  20. Thread: Trane voyager

    by MUNC
    Replies
    27
    Views
    2,415

    Sounds like you don't have but need a lock up...

    Sounds like you don't have but need a lock up reg____________________________________________________________


    I re-read my post, forgot to put the " - " in front of .20, I knew what I meant so...
  21. Thread: Trane Help

    by MUNC
    Replies
    2
    Views
    414

    Have you tried comfort site?

    Have you tried comfort site?
  22. Replies
    58
    Views
    4,295

    Since over seas started buying our beer cans and...

    Since over seas started buying our beer cans and sending back x-chngs it's been a prob. Also everything else on a carrier. How many stripped screw holes can you count on one RTU?
  23. Replies
    13
    Views
    1,311

    Def. need more info

    Def. need more info
  24. Thread: Vav filters

    by MUNC
    Replies
    13
    Views
    1,776

    You wouldn't believe how many fan powered vav...

    You wouldn't believe how many fan powered vav boxes with electric reheat I've had to replace high limits on from over tripping, had to replace burnt wires and terminals and blower motors. all due to...
  25. Thread: Expansion tank

    by MUNC
    Replies
    23
    Views
    1,663

    What about static head???? isolate and drain tank.

    What about static head???? isolate and drain tank.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event