Search:

http://www.icmcontrols.com sc-3801 for your 2 stage best thermostats out there today !!!!!

take a look at http://www.goodmanmfg.com & see what they have in print about warranteeing unit purchased over the internet.

i know a guy that says the dish on top of wally-world is the cause of all the bad in this country. home depot is backing them up too.

gas pressure could be a problem. valves are designed to close with too much pressure. be safe,CALL A MILLER TECH!!!!!

nothing wrong with a beckett nx. very nice burner as a matter of fact. once you get used to them you'll like them.

been selling them 15 yrs & no problems yet. although, i do size & install them properly. does make a difference.

10 gauge heat exchanger on the centennial. 14 gauge radiator. no heat exchanger problems with the cenntenial. you're thinking tempomatic. can't see the big deal over a copper spraypainted radiator....

go with a williamson centennial. 10 gauge heat exchanger,beckett burner. thermopride,13 gauge heat exchanger,italian burner tough to get parts for.

nordyne has a 40,000 90% http://www.nordyne.com

why do you want to lose all those btu's by switching to ng? it gonna cost you almost 30% more on ng. at least you're not on lp.

yellow markers ?

maybe nordyne tech service can help. have model & ser # when you call. 1-800-422-4328 & press 2

i just put in one of those 93% "army furnaces" 2 weeks ago. only thing i wasn't too crazy about was the condensate drain/trap setup. woulda liked a j trap better. runs real nice though. i think i...

where are you? how old is your furnace? your model# is
cmf 80 po serial # ? when was the last time it was OPENED UP & cleaned ?

too bad buford pusser's not around to fix that kimd of stuff.

they run good with a beckett nx too

http://www.icmcontrols.com
good stuff.

is your condensate drain working properly? i had an m2 once that was popping & going off on vent safety & it was because the drain line was kinked & water was boiling in the hx.

there's a kit you can get so you can gut a roof jack & go straight up through the roof. eliminates the bends. may work for you. don't have the part #. call tech service & ask for tom s.,he'll get it...

maybe it's because of turbulence or something. long radius elbows? static pressure test will tell. you don't have insulation or anything in the inducer or heat exchanger do you? i had one where the...

also,your intake is not sucking in exhaust air is it?

i had a vent safety switch tripping on an m3. it was a draft in the wall behind the thermostat.(marriage wall)caused the furnace to short cycle. sounds like you need to do a static pressure test....

maybe you'll get lucky, & some cold dreary night you'll get to work on that cop's furnace & show him what a beating HIS wallet can take.

you could always use an electric furnace with a split system ac. try an e3eb furnace from nordyne. ac ready & all. nice furnace! available in all their brands. http://www.nordyne.com

don't forget george " the animal" steele, or ivan putski

i thought xenon was a private label amana for airtime 500/one hour heating & ac.

if you want a 90+ try a miller/intertherm M3RL. very nice furnace for a gas furnace. made for manufactured housing. ac ready. http://www.nordyne.com

is it a coleman or is it an intertherm? you might want to look at the label. coleman is made by york. intertherm is made by nordyne. the nordyne is the way to go. go to colemanac.com & look at the...

2hot2coolme you must be WAY OVERSIZING them if you think they're noisy. i happen to think they're very good units. very low repair calls. sturdy,easy to repair on the rare occasion they need work....

outside square footage x 20. vaulted ceiling add 1/2 ton. skylights add 1/4 ton each. it never misses.

williamson still makes a great oil furnace.

i ordered a part from them the other day. maybe they can tell you something. http://www.glowcoreac.com 1-800-676-4546

no they don't. they're just like a residential system. that t- 87 should have a subbase & red to rh & rc,green ,white,& yellow. then yellow & black to the condenser from furnace. should be a manual...

mike patriak boces liverpool,ny excellent teacher. even with the brooklyn accent.

#1 & #2 oil hot water & tide. #4 & #6 wash in lestoil,then wash in tide or wisk.

yep that's why i mentioned nordyne,QUALITY!!!! Fact!!!
you young pups that follow the latest fad don't know about stuff like that.

take a look at tappan,westinghouse,frigidaire. whichever is available in your area. i think you'll like them. http://www.nordyne.com

dunkirk is a very good boiler. brother to the utica boiler. williamson also has a boiler. it's made by their parent weil-mclain. i would stay with beckett. they don't need to be adjusted throughout...

dunkirk is avery good boiler. brother to the utica boiler. williamson also has a boiler. it's made by their parent weil-mclain. i would stay with beckett. they don't need to be adjusted throughout...

i think you'll find the williamson centennial a very nice furnace. quiet, easy to maintain,sturdy. stay away from the temp-o-matic. the centennial is the best one. tappans are nice too,8 year...

i think we'd be better off if harry was still here minding the store. or col.potter.

where in the sam hill is norfork? wouldn't be norfolk,va.?,eh?

those new "army" furnaces are better than the old ones. ac's too. don't they look like army green?

going miller would be better.

don't forget to consider : oil = 140,000 btu per gallon
nat gas = 100,000 per therm lp = 91,000 per gallon. oil is still your bet fuel,the burners are just as clean as gas when done right. ...

GENESEE , ice cold. MMMMMMMMM!!!!!!!

one supplier in my area is saying he's going all 13 seer for next season. he's going to have as little 10 seer as possible. another one said he's gonna have 10s as far as the eye can see. it'll be...

warranties on nordyne products go directly through nordyne. they even have their own in house extended warranty. http://www.nordyne.com you won't find maytag products on nordyne's site. maytag is...

mike patriak, ocm boces adult ed teacher in liverpool,ny is the best!!! used to work in the lab at carrier & in the field. excellent teacher. his brooklyn accent is still there though.

you tie into one lug of the line side. not the load side. so far the code guys up here haven't said anything about them not being code approved. we have to have licenses & permits in syracuse.