Search:

Type: Posts; User: generaltech1

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    18
    Views
    286

    I looked up the documentation and it says its a...

    I looked up the documentation and it says its a 1k.
  2. Replies
    18
    Views
    286

    For testing, can i jumper in a 1k resistor?

    For testing, can i jumper in a 1k resistor?
  3. Replies
    18
    Views
    286

    As far as i know, its the original sensor.

    As far as i know, its the original sensor.
  4. Replies
    18
    Views
    286

    I was in contact with the manufacturer this...

    I was in contact with the manufacturer this morning and given that the outside temp was approx, they told me that it was close, its a 10k sensor.
  5. Replies
    18
    Views
    286

    So terminal #1 of the analog inputs is set for...

    So terminal #1 of the analog inputs is set for temp.
  6. Replies
    18
    Views
    286

    As it sits right now, SW1: 1-3 on, 4 off, 5-6 on....

    As it sits right now, SW1: 1-3 on, 4 off, 5-6 on. SW2: 1-3 off, 4 on, 5-6 off.
  7. Replies
    18
    Views
    286

    And which terminal should the oat sensor be...

    And which terminal should the oat sensor be connected to?
  8. Replies
    18
    Views
    286

    And ive never programmed or reprogrammed a...

    And ive never programmed or reprogrammed a controller, but ive always wanted to.
  9. Replies
    18
    Views
    286

    Not sure which one was the correct one since the...

    Not sure which one was the correct one since the wire that that was labeled for the oat was cut. I did connect a new sensor directly to the board, but no change.
  10. Replies
    18
    Views
    286

    Metasys UNT

    I have an OAT sensor that reads "??? 250*f" on the front end, the sensor and the wiring ohm out ok, I got 17 w/ an OAT of about 56*. Does it matter what analog input terminals I use for the OAT? Im...
  11. Replies
    1
    Views
    465

    Hobart 2912 slicer

    This slicer no longer works in auto mode. I was wondering what I need to look for on this, is it merely just a switch? I had this apart about 3 weeks ago to replace the on/off switch and I really...
  12. Replies
    4
    Views
    526

    I did trace the wires and the donuts are...

    I did trace the wires and the donuts are connected to the controller. Thanks
  13. Replies
    4
    Views
    526

    Metasys CT

    Ok, having mainly a residential background, not having to have dealt with this before, I need some advice and/or guidance on how to correct an issue with a building's CT that shows that its offline...
  14. Replies
    23
    Views
    1,689

    Ive heard of Tony MacAlpine, but never heard/seen...

    Ive heard of Tony MacAlpine, but never heard/seen him play, until now! He kicks ass!!!
  15. Replies
    13
    Views
    3,879

    Ive so far found that the cooling fans were CAKED...

    Ive so far found that the cooling fans were CAKED with grease and dust, im going to clean them first. And follow up with all your suggestions. Thanks!
  16. Replies
    4
    Views
    849

    After replacing every component in the ignition...

    After replacing every component in the ignition system, it lights, but goes out immediately! I would say flame sensor, but that has been replaced as well!!
  17. Replies
    4
    Views
    849

    Groen Smart Steam

    M: SSB5G S:J77748B-1-1
    This dang steamer has been a bur under my saddle for the past year, luckily their are three others that they can use. I have gone thru this unit with a fine tooth comb,...
  18. Replies
    19
    Views
    1,656

    That's another thing...I have never...

    That's another thing...I have never reallyunderstood sh/sc...can someone splain it in english?
  19. Replies
    19
    Views
    1,656

    Gauge Reading

    Ok yeah Im not that good at reading my gauges, I admit that, but here goes. R22, 91*ambient, suction 75#, discharge 300#, low on refrigerant? Im only getting about 60* DA temp. Room temp is about 76,...
  20. Replies
    2
    Views
    839

    Groen SSB5G

    Im desperately looking for an actual service manual for an SSB5G/J777-48-B-1-1, not the operator manual. Anyone out there have a link to get one or have one that can be emailed to me? Thanks in...
  21. Replies
    13
    Views
    3,879

    Ill check into that.

    Ill check into that.
  22. Replies
    8
    Views
    1,131

    The 1st one had a blown out relay on the fan...

    The 1st one had a blown out relay on the fan timer, but when I replaced it and the motor was finally getting power, it sounded bad. It took off slow, and ran for a while, unitl tstat was satisfied...
  23. Replies
    8
    Views
    1,131

    yes 24v to the module

    yes 24v to the module
  24. Replies
    13
    Views
    3,879

    Blodgett DFG1XL/AA

    S/N 092107RI0492-Ive had numerous calls on this unit, but I cant ever find a problem with it, yes the dreaded intermittent problem. Although the last time that I was there I set it to 350F, and...
  25. Replies
    8
    Views
    1,131

    pressure switch is closing

    pressure switch is closing
  26. Replies
    8
    Views
    1,131

    On the first unit, open limit @ hx, I jumpered it...

    On the first unit, open limit @ hx, I jumpered it out, it lit off, no power to motor on com and high. So I guess I need a board for that one.
    And on the 2nd unit, indoor blower operates, combustion...
  27. Replies
    8
    Views
    1,131

    Two ICP RTU gaspacks

    1st one PGME60H150C/G030612118..thermostat blank, all that's running is the combustion fan motor, no call for heat, got 24v into the control board, but nothing on any of the lv terminals on the...
  28. Replies
    2
    Views
    1,222

    CresCor warming cabinet H137UA12C208

    I get a call that its not heating. It has a tag on the back stating "Wired for 208 Volts", but no where am I getting 208V only 120v. I called CresCor tech support since I didnt have any tech...
  29. Replies
    3
    Views
    1,746

    Blodgett oven calibration

    Model #: DFG-100-XCEL-DOUBLE. I was wondering if somehow this oven is calibrated differently than others, and if so, what is the correct procedure. I have calibrated a variety of ovens over the...
  30. I know that this thread is well over 5 years old,...

    I know that this thread is well over 5 years old, but it doesnt hurt to ask. I was also looking for a copt of the Maple-Chase 9700 thermostat manual, if anyone out there has a copy, give me a shout....
  31. Replies
    2
    Views
    730

    Trane on Metasys

    Ok ill try to make this short as I can. I have little experience on commercial and no training or experience with Metasys. These are Trane package units of various sizes that are cooling...
  32. Replies
    12
    Views
    797

    What are your thoughts.........

    As a group, what are your thoughts on a fellow employee that runs to the boss every time they have a "problem" (the problem being a comment made jokingly, and not a comment of a suggestive or...
  33. Thread: US Range

    by generaltech1
    Replies
    2
    Views
    946

    US Range

    I cannot seem to find a model and/or serial # on this unit. Can anyone tell me where I might be able to find it? Its about 10 years old(guesstimate). The problem is that the pilot wont stay lit...
  34. A bobcat walks into a bar...............

    Youve got to see it to believe it:
    http://www.myfoxphoenix.com/dpp/news/Bobcat_Attacks_Inside_Cottonwood_Bar
  35. Replies
    3
    Views
    771

    Ahem....well thats 1:47 of my life i'll never get...

    Ahem....well thats 1:47 of my life i'll never get back, thanks.
  36. Replies
    1
    Views
    853

    Been there many ti... ugh, um...

    Been there many ti... ugh, um uhhhhhhhhhhhh.....THUD! (j/k) But I have been there, the food kicks the crap outta HOOTERS, and the nurses aint too bad to look at neither!
  37. Replies
    14
    Views
    3,633

    The flex line disappears into the attic, I dont...

    The flex line disappears into the attic, I dont see a shut off, drip leg or a union. And the dryer vents right next to the unit, I hope thats not a return grill by the trash can that would be...
  38. Replies
    12
    Views
    2,416

    WTH???!! What a mess!! To me it seems that in...

    WTH???!! What a mess!!

    To me it seems that in cases like this, it wouldve taken a lot less work and time just do the damn job right! Some people just have no pride in thier work anymore.
  39. Replies
    98
    Views
    16,539

    Nice job! Too bad the customer didnt have the...

    Nice job! Too bad the customer didnt have the good sense to accept your bid from the start, "penny smart, but pound foolish", as the saying goes.

    One question though...shouldnt the furnace exhaust...
  40. Replies
    3
    Views
    2,003

    HVAC/R Preventive Maint. Checklist

    Does anyone have a PM checklist, or can point me to where I can find a printable version, thanks.
  41. Thread: Walk In

    by generaltech1
    Replies
    5
    Views
    706

    Walk In

    We have a walk-in refer that shares a wall with our walk-in freezer. At the base of the wall of the freezer, on the refer side there's a formation of ice that runs the full length of the wall. ...
  42. Replies
    52
    Views
    6,214

    Kewl, thanks!

    Kewl, thanks!
  43. Replies
    52
    Views
    6,214

    'nuff said. I appreciate all your help/advice.

    'nuff said. I appreciate all your help/advice.
  44. Replies
    52
    Views
    6,214

    So...what is our name?

    So...what is our name?
  45. Replies
    52
    Views
    6,214

    I sympathize with the HSM, I felt the same way...

    I sympathize with the HSM, I felt the same way that these units are a $$$$ pit!
  46. Replies
    52
    Views
    6,214

    It has an anode rod, like a water heater tank?

    It has an anode rod, like a water heater tank?
  47. Replies
    52
    Views
    6,214

    Hobart Service Manager was out before I got here...

    Hobart Service Manager was out before I got here and they threw about 7g in parts at it and the problem continued. if I could get it solve I would be a freekin' hero, but 2G?
  48. Replies
    52
    Views
    6,214

    Holy Crap! $2000.00!!!?? There has been at least...

    Holy Crap! $2000.00!!!?? There has been at least 7G in parts put into this thing already!
    Oh and the screws, there may be 8, im not sure right now.
  49. Replies
    52
    Views
    6,214

    Yes 6 philips head

    Yes 6 philips head
  50. Replies
    52
    Views
    6,214

    Do you have a part # for the upgrade? And was...

    Do you have a part # for the upgrade? And was that that correct, $2000.00?!!
Results 1 to 50 of 596
Page 1 of 12 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event