Search:

Type: Posts; User: northeastnewbie

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    2,198

    I had to ask a customer who they pissed of when I...

    I had to ask a customer who they pissed of when I explained how their units had stages of cooling "manually disabled". They replied that a review of tapes would take place.
  2. Replies
    33
    Views
    891

    Ditto to what airflow said. Had to do it like...

    Ditto to what airflow said. Had to do it like that in an old school one time
  3. Replies
    55
    Views
    8,428

    Seen that happen before except it was on three...

    Seen that happen before except it was on three twenty ton carriers. Oh and the inspector passed it. GC upset with me when I wouldnt startup the units.
  4. Replies
    15
    Views
    966

    One was inside just in an exterior wall. Warming...

    One was inside just in an exterior wall. Warming up now but had a deep freeze for us in massachusetts this past week. And ya the one piped down the side of the house was some jerk being cheap sucks...
  5. Replies
    15
    Views
    966

    drain freeze

    Two frozen drain lines in the course of my day today 90% furnaces shutting down on pressure due to frozen drains in exterior wall. My question is does anyone have a good way to thaw them out or any...
  6. Replies
    76
    Views
    3,423

    Had to do one of those alone last year. What a...

    Had to do one of those alone last year. What a horrible eight hour day. Did manage to get fifteen minutes out of the companies other/ lead tech to swing by and hold it in place till I got enough...
  7. Have a shop make up a transition fitting to go...

    Have a shop make up a transition fitting to go between
  8. Batteries for cordless tools should be taken in...

    Batteries for cordless tools should be taken in each night not that I do but its getting to be a pain replacing them
  9. Replies
    31
    Views
    2,811

    Hold on I'm missing something. Who's pressurizing...

    Hold on I'm missing something. Who's pressurizing a system with air?
  10. Replies
    31
    Views
    2,811

    Hey superfitter that looks cool gonna mention it...

    Hey superfitter that looks cool gonna mention it to the boss monday maube go kust get one for myself thanks.
  11. Replies
    31
    Views
    2,811

    Yes it does. I'll be honest and tell you first...

    Yes it does. I'll be honest and tell you first time I've noticed that arrangement. Guess I've been lucky so far normally just searching for leaks on these rtus but if the header was the source of the...
  12. Replies
    31
    Views
    2,811

    My boss will sell anything. Depends on the job...

    My boss will sell anything. Depends on the job equipment spec and who's giving him the best price that day. I can expect to be setting lennox rtu one day in Worcester then setting up econmisers on a...
  13. Replies
    31
    Views
    2,811

    Well your right shouldn't take long except dinky...

    Well your right shouldn't take long except dinky recovery machine (appion g1) spits the 410 hot into the tank and its not long before you gotta stop to let tank cool and pressure drop or bye bye...
  14. Replies
    31
    Views
    2,811

    Yup started recovery took off for a long weekend...

    Yup started recovery took off for a long weekend and sent me in to finish recovery and charge back to nameplate without making any other changes. So I basically knew I was wasting time at that point...
  15. Replies
    31
    Views
    2,811

    The head was at 260. 75* day. System was slightly...

    The head was at 260. 75* day. System was slightly under charged but I couldn't see charging to full name plate if at 80% charge I pulling a vac on this scroll compressor. System hasn't been opened....
  16. Replies
    31
    Views
    2,811

    carrier rtu issues

    Brand new rtu short cycling compressor. Jump out low pressure switch to see just how low the suction pressure would drop while pulling 100% outdoor air. Damn near pulled into a vacuum. I'm going with...
  17. Replies
    7
    Views
    438

    Think he means reciprocating

    Think he means reciprocating
  18. Replies
    7
    Views
    478

    Even with a micro channel if its only the factory...

    Even with a micro channel if its only the factory charge in the system it should be able to hold the charge again. Right?
  19. Go through setup in the installers guide. The...

    Go through setup in the installers guide. The 8000 has to be programmed to use the remote sensor
  20. Replies
    1
    Views
    316

    Is power coming through relay when it clicks? Is...

    Is power coming through relay when it clicks? Is that voltage getting to the motor?
  21. Replies
    20
    Views
    3,394

    Better get something better than those throw...

    Better get something better than those throw aways even if its changed weekly
  22. Replies
    16
    Views
    1,415

    Was my post that bad? Could I have made it easier...

    Was my post that bad? Could I have made it easier to read?
  23. Replies
    16
    Views
    1,415

    Phm the second wire pull to replace the thought...

    Phm the second wire pull to replace the thought to be damaged wire was most definitely shielded wire and while the readings from three different meters still picked up tenbl less volts it was still...
  24. Replies
    8
    Views
    562

    Get a piece of patch metal maybe 24x24 cut a nice...

    Get a piece of patch metal maybe 24x24 cut a nice hole in the center of the front side of the plenum crawl in and repair/seal from the inside use duct seal not tape. Then your leak is right in front...
  25. Replies
    16
    Views
    1,415

    I've been re-reading my post and other than a...

    I've been re-reading my post and other than a couple spelling errors and a few examples of bad grammar I'm missing what you have me looking for. You also asked me to be patient and believe me I am...
Results 1 to 25 of 49
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event