Search:

Type: Posts; User: Zymurgist

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. A fix is in place. The Emerson field rep came by...

    A fix is in place. The Emerson field rep came by the site on Friday with some new information from Emerson/ALC tech support. I didn't get full details but when he left, the BV points that were...
  2. I spoke too soon. Problem not solved but on hold...

    I spoke too soon. Problem not solved but on hold instead!! The alarm time delay was changed to 20 million seconds (231 days) until ALC and Liebert can get a permanent fix.
  3. Problem solved! I'm happy to report that the...

    Problem solved! I'm happy to report that the Emerson (Liebert) field engineer dug deep for answers and spent time a good amount of time on the site to fix the problem. I don't understand what he did...
  4. I'm using Delta Controls Orcaview to see the...

    I'm using Delta Controls Orcaview to see the Sitelink Bacnet points and that's what Orcaview shows me. Is there a generic Bacnet application that may show more?
  5. Bacnet- what seems to be happening is that...

    Bacnet- what seems to be happening is that changes to the fields in the alarming tab have no effect. The check boxes come unchecked by default, the event classes are Event_Class_1 by default and...
  6. Maxburn, to answer your question about ignoring...

    Maxburn, to answer your question about ignoring alarms-yes Delta does provide several ways to filter/ignore alarms and that works fine. My controllers don't see them. The problem is that the alarms...
  7. They may not be set up as alarms but they are in...

    They may not be set up as alarms but they are in an alarm state and broadcast Bacnet alarms rapidly and repeatedly even though the check boxes are unchecked.
  8. Thanks for the replies. I've had an experienced...

    Thanks for the replies. I've had an experienced Liebert field rep to the site and after changing certain obvious settings in his devices the problem still persisted. He talked to one of the more...
  9. Sitelink SSW-12E Bacnet Module Alarm Problems

    I've got 2 Sitelink SSW-12E Bacnet controllers with 10 Lieberts on each one. They are addressed 5 and 6 and show up in my Delta Navigator on the same level as 4 DSM-RTR but are wired to the Net2 on...
  10. Replies
    5
    Views
    1,024

    Thanks for all of the suggestions. Again...

    Thanks for all of the suggestions. Again Honeywell has remolded something into a completely counter-intuitive guessing game. I'm used to using a throttling range that is a fraction of the range of...
  11. Replies
    5
    Views
    1,024

    Spyder static press PID settings

    Can't seem to get a stable output from a PID (overshoot-undershoot etc).
    I'm passing the static pressure from a VAV box to an AHU controller. Anyone have any starting points for my PID settings...
  12. Replies
    10
    Views
    908

    Thanks for the help guys. I'm at the job site...

    Thanks for the help guys. I'm at the job site this morning and have some things to do before I get back to trying to bind nvs. I'll try your suggestions later and let you know.
  13. Replies
    10
    Views
    908

    I did the program myself and am happy with it. I...

    I did the program myself and am happy with it. I understand generating nvs but am not sure what that has to do with using a LonSpyder for my controller or the Venom App.

    As far as tech support, I...
  14. Replies
    10
    Views
    908

    No, I'm using the LonSpyder from the...

    No, I'm using the LonSpyder from the HoneywellSpyderTool.
  15. Replies
    10
    Views
    908

    I deleted the MATemp proxy point and am trying to...

    I deleted the MATemp proxy point and am trying to add it from snvt_temp_p but I don't know where to find it. I looked through all my discovered points and see nothing.
  16. Replies
    10
    Views
    908

    Wow

    Thanks for the quick reply, Digo. You are correct on the first, I did the latter and will try the former. I'll also try your suggestion for my graphic config. You are my new tech support person.....
  17. Replies
    10
    Views
    908

    Spyder programming issues

    Since there is a plethora of Spyder experts on this forum, I have a couple of immediate problems that you all have probably run into. My experience is in Delta, Johnson and industrial PLC but my...
  18. Replies
    4
    Views
    1,283

    Thanks Rad1. That's been suggested and I'll have...

    Thanks Rad1. That's been suggested and I'll have to try it. I'm a little surprised that it hasn't been written already and available from Honeywell given the popularity of FP hot water valves in VAV...
  19. Replies
    4
    Views
    1,283

    Honeywell Venom app for VAV w/fp hw valve

    This is my first spyder job. I'm using WEBstation AX 3.4.43. I've been through AX certification and fell comfortable with the AHU, chiller and boiler programming I've done so far. The...
  20. Replies
    4
    Views
    677

    It's a Spyder (PUL6438S) for and AHU variable air...

    It's a Spyder (PUL6438S) for and AHU variable air volume unit. I need to maintain a minimum cfm OA flow for ventilation. The PID output goes negative anytime I go above the deadband. Current settings...
  21. Replies
    4
    Views
    677

    Webstation-AX Airflow PID settings

    This is my first AX programming job after years of PLC, Johnson and Delta Controls. I need some suggestions on PID settings for OA damper control based on an OA flow station input. My temperature...
  22. Replies
    7
    Views
    522

    Use a "switch" if your software iteration has the...

    Use a "switch" if your software iteration has the "switch" function. ORCAView has had it for a while.

    PumpOutput = Switch(PumpOutput,Tanktemp,95,105)

    This will turn your pump on at 95 and off...
  23. Replies
    12
    Views
    814

    THe SUA object that you created has to use the...

    THe SUA object that you created has to use the SUG object that exists. The SUGs are e.g. Administrator,Operator, etc. Most likely you assigned the Administrator SUG to your new SUA. Check the...
  24. Replies
    12
    Views
    814

    Also check the computer's SUG object in...

    Also check the computer's SUG object in Navigator. See attached screen capture. This is a way to restrict access to certain controllers. It sounds like your issue.
  25. Thread: Delta DNA

    by Zymurgist
    Replies
    12
    Views
    883

    Also note that if you're connected directly to...

    Also note that if you're connected directly to the ethernet port on a router (DSM-RTR) or DSC, you need a crossover ethernet cable. If you go through a switch then it doesn't matter.
Results 1 to 25 of 55
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event