Search:

Type: Posts; User: edwardjw

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    906

    Check your email hopefully thats what you want.

    Check your email hopefully thats what you want.
  2. Thread: Lennox Help

    by edwardjw
    Replies
    8
    Views
    1,259

    Kevin is correct oem is best but i do think icm...

    Kevin is correct oem is best but i do think icm makes a replacement board that johnstones carries. When you pull old board look on the back of it have found several with short marks on them. good...
  3. Replies
    33
    Views
    2,138

    Call a plumber have him send his camera in the...

    Call a plumber have him send his camera in the ductwork ive never tried that just an idea
  4. I put Protreat in all evaporator pans that i...

    I put Protreat in all evaporator pans that i service and havent had any problems so far two years going.
  5. Replies
    1
    Views
    591

    Its just to make the match with the width of your...

    Its just to make the match with the width of your furnace both are rated the same otherwise.
  6. Replies
    4
    Views
    518

    I love them use to move pop machines with one and...

    I love them use to move pop machines with one and it would climb with no problems.
  7. Replies
    2
    Views
    656

    Are you in the trade because this is a no diy...

    Are you in the trade because this is a no diy site.
  8. Replies
    2
    Views
    420

    Thank you very much

    Thank you very much
  9. Replies
    2
    Views
    420

    Lennox G230213-75-2

    I know i should know this but could somebody give me a width for this furnace I looked at it four months ago and now im installing a new furnace tommorow and cant remember if its 14 or 17 inches wide...
  10. Replies
    44
    Views
    4,237

    I just installed a 40,000 btu furnace in a...

    I just installed a 40,000 btu furnace in a similar house as yours and it took all of 7 hours of running the furnace to get the slab to heat up.I told the home owner the losses up front and showed him...
  11. Replies
    10
    Views
    1,846

    Always hardpipe through cabinet then flex from...

    Always hardpipe through cabinet then flex from there but try to hard pipe the whole way.Also galvanized pipe is a not allowed have seen it but inspectors would fail it here.
  12. Replies
    4
    Views
    657

    :oops:

    :oops:
  13. Replies
    4
    Views
    657

    carrier Van broke down today so dont have model...

    carrier Van broke down today so dont have model numbers with me gas was off but power was on then would be shut off then on again to show property.Will post some model numbers tomm thanks
  14. Replies
    5
    Views
    2,787

    Just out of curiosity why would all the wires be...

    Just out of curiosity why would all the wires be cut? Ive only seen that done when there is a cracked heat exchanger and the tech does want home owner to try and put it back together.
  15. Replies
    4
    Views
    657

    Inducer motor failures

    Just got an account has 54 furnaces that havent been run for at least two years out of nine rooftops four inducer motors dead.Then 12 of the 26 split systems inducer motors are bad.Is this typical of...
  16. Replies
    38
    Views
    2,743

    Have you let the furnace run through a complete...

    Have you let the furnace run through a complete cycle yet to see if it will.And about the wiring the fuse was put in to protect the system.If its just a wiring issue then it shouldnt be that bad to...
  17. Replies
    12
    Views
    39,752

    You might look into buying a Prestons Guide very...

    You might look into buying a Prestons Guide very nice to have when you start out.
  18. When I worked at a welding shop we use to take a...

    When I worked at a welding shop we use to take a peice of plate drill hole in it same size or a bit smaller and tig weld the pin to the plate.Let it cool then twist while pulling up and if it didnt...
  19. Replies
    5
    Views
    827

    Three years.

    Three years.
  20. Replies
    5
    Views
    827

    Installed 5 so far and havent had a problem yet...

    Installed 5 so far and havent had a problem yet kinda nice setup.
  21. Thread: WINE CELLAR

    by edwardjw
    Replies
    6
    Views
    699

    Poor oil return or no oil return.

    Poor oil return or no oil return.
  22. Replies
    0
    Views
    567

    Coleman PAC042H1021A

    I was installing electric heat on this unit today and after looking at schematic and I dont think I have the right kit 09WSJ1502B.From the wiring diagram cant see how this kit would work as supplied...
  23. Thread: SUPER SEAL

    by edwardjw
    Replies
    7
    Views
    540

    Only used it once customer wanted to try it on...

    Only used it once customer wanted to try it on his system dad six holes in the evaporator.I mrked them put it in the system and charged sytem up came back the next day and no leaks got a call two...
  24. Replies
    3
    Views
    508

    Could you take the number off of the compressor...

    Could you take the number off of the compressor and then contact a supply house for a cross.
  25. Replies
    15
    Views
    894

    Did you consider RX flush then blow out with...

    Did you consider RX flush then blow out with nitrogen. Just my opinion.
Results 1 to 25 of 43
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event